JavaScript Disabled - Unable to show Cart
There are (185) parts used by this model.
- Found on Diagram:
Brake
-
11022003
BRAKE DRUM
16" outside diameter. Cast iron material.
$156.13
-
11022010
BRAKE DRUM
Cast iron type. 16" outside diameter, 13 7/8" inside diameter.
$121.68
-
-
-
-
-
-
11022900
BRAKE DUST SEAL
Ozone resistant material, steel base. Brake dust seal for diesel and gas applications.
$4.94
-
11022901
No Longer Available
-
11025503
BRAKE DISC
OD is 8.07", ID is 2.10", 22 teeth. 0.750" Facing, Brake disc for diesel and gas applications.
$40.43
-
11025506
BRAKE DISC
6" outside diameter w/60 external teeth.
$5.40
-
11025507
BRAKE DISC
OD 8.22", ID 4.48", one notched oblong end. Brake disc for diesel and gas applications.
$8.73
-
11025516
FRICTION DISC
8" diameter, 22 tooth inside spline disc, 1.125" Facing
$40.18
- Found on Diagram:
Cooling
-
-
-
11066110
RADIATOR CAP
Radiator Cap rated for 13 psi. Overflow reservoir systems, 3/4" neck
$6.04
-
-
11066200
WATER PUMP
Front pump only, single groove v-belt pulley. Mounting holes 5/16" and 7/16" and will replace earlier units w/smaller mounting holes. Includes both pump and housing gaskets (Atlantic #E6NN8513AA and E5NN8507AB).
$64.58
-
11066201
WATER PUMP
Front pump only, double groove v-belt pulley. Includes both pump and housing gaskets (Atlantic #E5NN8507AB).
$114.77
-
11066204
WATER PUMP
Single pulley hub for bolt on fan, complete pump including back plate. For models w/o heater plug or cab heater.
$95.27
-
-
-
11066294
RADIATOR HOSE
Upper Radiator Hose 1 1/2" I.D. for Gasoline Models.
$13.64
-
11066297
FAN SHROUD
Fiberglass type must drill holes for proper fitment.
$85.36
-
-
-
-
-
-
-
-
11066310
RADIATOR HOSE
1.5" inside diameter, upper hose for Diesel models.
$6.34
-
- Found on Diagram:
Electrical
-
11000100
5IN DIESEL STARTER
OE Lucas unit. DD, 2.8KW, 12v, 10 tooth drive. Uses D2NN11390A solenoid. Uses E4NN11350AA drive. Starter for Ford/New Holland diesel applications.
$246.79
-
11000100A
STARTER, AFTERMARKET
12v, 10 tooth, 2.8KW. Aftermarket unit, not OE Lucas, as 83981923. Uses D7NN11390B Atlantic solenoid and C5NF11350C Atlantic drive. Note: Warranty is six (6) months from date of purchase, unit replacement only. Starter for Ford/New Holland diesel applications.
$217.22
-
11000105
STARTER
Gear reduction option for D8NN11000CE. Starter for Ford/New Holland diesel applications.
$235.95
-
11000112
STARTER
12v, 10 tooth, DD unit. Uses C5NF-11A108-A drive. Uses D2AF11450A solenoid. For 3 Cylinder Gas.
$190.64
-
-
-
-
-
11000300
STARTER DRIVE
10 tooth, CW, fits 3 splinw armature, 17mmID, 40mmGr, 70mmL, 60mmOD.
$46.46
-
11000301
STARTER DRIVE
For 4.5"Lucas (M45), 10 tooth, CW, fits 12spline armature, 17mmID, 40mmGr, 70mmL, 60mmOD.
$58.42
-
11000302
STARTER DRIVE
10 tooth, CW, fits 12spline armature, 17mmID, 40mmGr, 73mmL, 60mmOD.
$53.66
-
-
11000410
BATTERY CABLE
34" Length. Negative battery cable for diesel and gas applications.
$24.30
-
11000411
BATTERY CABLE
36-1/2" Length. Positive battery cable for diesel and gas applications.
$34.56
-
11000500
ALTERNATOR
70 amp unit w/battery sensor. D+, D+, B+ and W terminals. Has 'Lucor' connector as well under plastic terminal protector.
$166.80
-
110005004
ALTERNATOR
12v, 45a, IR, EF, clockwise, Lucas replacement
$157.26
-
-
11000540
COIL
6v (w/o resistor) or 12v (w/resistor), oil filled. Includes bracket and resisitor.
$18.96
-
11000550
REGULATOR
12v, 14.1 volt set, Four prong (two male-two female) connector for Motorolla style alternators w/external regulator. Fits ref#'s D5NN10300D and D5NN10300E. If regulator is not used with correct alternator, unit will not charge. Non-adjustable.
$38.92
-
11000553
REGULATOR
12v, 14.4 volt set, A-circuit, W/battery temp sensor. Fits ref#'s E7NN10B376AB, BB, E3NN10B376AD (Atlantic 81863039, 81863039, 81868798). Fits Lucas/Marelli units.
$43.24
-
11000560
REGULATOR
12v, round terminal plug with four male connectors. Fits units w/Motorolla equipped.
$79.73
-
11000600
GENERATOR
12v, 22amp, uses 105E10505C regulator. W/Fan and tach drive. Pulley seperate, use C5NF10196B. 1965 on up units.
$140.79
-
11000650
REGULATOR
12v, B circuit. Use with C5NF10000E Lucas generator. 1965 and up units.
$26.77
-
11000651
GENERATOR FAN
For C5NF10000E. Fits Lucas tach drive generator on 2000~7000 series.
$8.71
-
-
11000653
TACH GEAR
For Lucas generators. Fits C5NF10000E.
$7.26
-
11000654
TACH DRIVE ASSEMBLY
For Lucas tach drive generator. Fits Atlantic C5NF10000E. Assembly w/gear and housing.
$21.62
-
-
-
-
11000906
BULB
14v maximum, 3.8 watt, miniature bayonet base. Priced individually, sold in multiples of 10. Bulb for diesel and gas applications. Type 1895.
$1.07
-
11000909
BULB
12v, 27/8.3 watt, double bayonet base. Type 1157. Priced individually, sold in multiples of 10.
$0.63
-
11000910
BULB
12v, 12.40 watts, rigid loop base. Bulb for diesel and gas applications. Type 561.
$2.59
-
11000912
BULB
12v, 4.3 watts, miniature bayonet base. Priced individually but sold in multiples of 10. Type 1816.
$0.44
-
11000914
BULB
12v, halogen, single spade halogen collar base. Type H1-55.
$6.49
-
11000915
BULB
12v, 60/55 watt, P43T base. Bulb for diesel and gas applications. Type H4-60P43.
$6.49
-
11000916
BULB
12v, 55 watt, PK22S base. Bulb for diesel and gas applications. Type H3-55.
$4.88
-
11000918
BULB
12v, 1.70 watts, miniature bayonet base. Priced individually, sold in multiples of 10. Type 53.
$1.72
-
11000931
FUSE
AGC5, Priced Individually, Sold in Multiples of 5
$0.33
-
11000933
FUSE
AGC15 fuse for diesel or gas applications, Priced Individually, Sold in Multiples of 5
$0.30
-
11000935
FUSE
AGC25 Fuse for diesel and gas applications, Priced Individually, Sold in Multiples of 5
$0.33
-
11000937
FUSE
AGC10, Priced Individually, Sold in Multiples of 5
$0.33
-
11000950
DIESEL STARTER BUSHIN
17.10mm ID, 21.04mm OD, 22.10mm L. Sintered brass material. Starter bushing for diesel applications.
$2.35
-
11000960
IGNITION SWITCH
Seven terminal Lucas type with cold start. Rated at max 35 amp load. Ignition switch for diesel and gas applications.
$13.34
-
11000967
STOP SWITCH
Two prong terminal. Stop switch for diesel and gas applications.
$19.49
-
11000968
IGNITION KEY
Priced individually, sold in multiples of 2. Ignition key for diesel and gas applications.
$1.91
-
11000969
STOP LIGHT SWITCH
12V Stop Light Switch for diesel and gas applications. Two connectors.
$29.24
-
-
11000978
LIGHT SWITCH
Fits numerous 1965~, 3-4-6 cyl's, rotary type switch. Light switch for diesel and gas applications.
$14.63
-
11000984
HOLD DOWN W/ NUT
1965~, 7" L by 5/16"x18 thread pitch. Battery Hold Down with nut for diesel and gas applications.
$3.66
-
11005108
IGN KIT INC. POINTS,
For OHV 3 cyl models. Ignition kit for gas applications.(inc. points, cond, rotor, plug)
$23.83
-
-
11006005
REAR LAMP LENS
Red Lens, tail light / brake light lens, fits original style housing.
$24.29
-
11006015
HEADLAMP
Headlight assembly, 12 volt sealed beam
$60.58
-
11006102
DISTRIBUTOR
For 3 cyl gas engines. Mechanical advance only; No provision for vacuum advance
$281.68
- Found on Diagram:
Front Axle & Steering
-
11044008
SPINDLE BEARING
ID is 1.345", OD is 2.2", Width is .622". Spindle bearing for diesel and gas applications.
$6.61
-
11044018
SPINDLE BUSHING
Height 1.482", OD 1.380", ID 1.25" Spindle bushing for diesel and gas applications.
$4.75
-
11044019
LINK END ASSEMBLY
Front side, 4" center to end, .687" shaft diameter w/18 pitch LH thread.
$14.85
-
11044020
LINK END ASSEMBLY
Rear angled shaft end 4 1/2" LOA, .687" diameter w/18 pitch RH thread.
$14.85
-
11044024
SPINDLE
RH, 11.687"L, 1.25" Upper diameter, 1.340" Lower diameter, 1.25" Inner stub diameter, .750" Outer stub diameter. Keyway is .235"W x .914"L.
$108.26
-
11044026
SPINDLE
LH, 11.687"L, 1.25" Upper diameter, 1.340" Lower diameter, 1.25" Inner stub diameter, .750" Outer stub diameter. Keyway is .235"W x .914"L.
$106.11
-
-
11044030
SPINDLE SEAL
OD: 1.71" (43.4mm), ID: 1.25" (31.8mm), W: 0.21" (5.3mm).
$1.99
-
11044031
AXLE PIN
Solid Axle Pin. OD: 1.750", Shaft L: 5.960". Can replace C5NN3127A.
$45.07
-
11044033
AXLE BUSHING
Front axle bushing, 2.19" outside diameter, 2.05" inside diameter, 1.5" length, non-split design w/inner spiral relief for lubrication. Axle bushing for diesel and gas applications.
$5.40
-
-
-
-
11044047
SPINDLE BEARING
Spindle bearing for diesel and gas applications. Greasable, ID: 1.50", OD: 2.25", WOA: 0.78".
$9.31
-
11044048
DRAG LINK END
3/4" by 16 pitch LH threads, 9/16" pin. Drag link end for diesel and gas applications.
$22.52
-
-
-
-
11044064
STEERING NUT
Steering nut for diesel and gas applications. 11/16" x 24 pitch (NF)
$6.39
-
-
-
-
-
11044087
STEERING SHAFT
Ball Nut and Shaft assembly. LOA: 26.57" (675mm), 36 spline, 11/16" 20 UNF thread.
$362.00
-
11044111
SPINDLE
Spindle for diesel and gas applications. RH
$136.46
-
11044112
SPINDLE
Spindle for diesel and gas applications. LH
$136.46
-
11044170
SEAL
Spindle dust seal with seal with groove and offset rubber for steering arm. OD: 1.71" (43.4mm), ID: 1.25" (31.8mm), W: 0.21" (5.3mm).
$2.13
-
-
11044184
DRAG LINK
Tube Length 28.125" (714.375mm), Overall length 30.10" (790mm)
$135.15
-
-
-
11044211
FRONT AXLE
Front Axle Center section, includes C7NN3153B bushing
$242.67
-
11044401
STEERING ARM
Spindle steering arm, for manual and power steering models, replaces 957E3130.
$57.93
-
11044450
STEERING GEAR ASSEMBL
Manual steering gear w/18" mainshaft. Sector shafts use D9NN2N289AA seals, already installed. Steering gear assembly for diesel and gas applications.
$648.12
-
11044554
TIE ROD
Outer tie rod end, right hand, thread ID: 3/4-16 UNF, usable length: 4.34" (110.24mm). Fits cab models built 4/1/1976 and later. (10 Series, 234, 334 and 335 British built only)
$78.78
-
11044900
STEERING WHEEL
18" Diameter center hub is 0.785 in, 36 splines. Steering wheel for diesel and gas applications.
$42.25
-
-
11044902
RADIUS BALL CAP
Radius ball cap used w/C5NN3N442C socket. Can be used for LH or RH side. Radius ball cap for diesel and gas applications.
$17.77
-
11044903
RADIUS SPACER
Radius rod socket, used w/ 83924040 cap. Can be used for LH or RH side.
$21.01
-
11044906
STEERING WHEEL
36 Spline inner hub, 15" Outer rim diameter, PVC grained cover material. Steering wheel for diesel and gas applications.
$49.03
-
-
11045218
BEARING CUP
Tapered Cup OD: 2.33" (59.18mm), ID: 2.24" (11.68mm), W: 0.46"
$3.15
-
11047077
SEAL
Seal, steering shaft. For 2-wheel drive models. OD: 1.39" (35.31mm), ID: 0.87" (22.09mm), W: 0.37" (9.39mm)
$9.12
- Found on Diagram:
Fuel
-
11030051
CARB FLOAT
Brass material float chambers. W/o pin.
$12.25
-
-
-
-
-
11033199
INJECTOR SEAL KIT
For all FNH 'long body' type injectors. Includes cork dust seal, copper compression seal and 2 aluminum return line seals.
$2.81
-
11033200
INJECTOR
Does not include washers, order 1103-3199 seal kit for washers and cork seal. Open Pressure 200-216.
$77.24
-
-
-
-
-
11033400
FUEL TANK
13 gallons (49.2 litres), for units equipped w/lock ring fuel sender. Fill neck height 2". Note: Will not fit 4000 models. Does not include lock ring or fuel tap. Does include fuel cap.
$193.34
-
-
-
11033404
FUEL SENDER
For fuel tanks using lock ring design sending unit. Fits Atlantic E3NN9002AB. Fuel sender for diesel applications.
$56.89
-
11033407
FUEL TAP
Tank tap is 7/8" tapered by 14 pitch, fuel line is 1/2" by 20 pitch.
$14.20
-
11033408
FUEL BOWL
Flat bottom type. Fuel bowl for diesel applications with 1" bottom hole.
$6.78
-
11033409
FUEL TANK
Original style Lock Ring Fuel Tank, for tractors equipped with lock ring type sender, does not include gasket, lock ring, fuel cap or fuel tap. Can replace E3NN9002KB fuel tank if D8NN9A316KA sender, E2NN1276AA gasket and C5NN9N283A twist lock are used.
$238.33
-
11033411
FUEL TAP SCREEN
Replaceable plastic fuel screen filter for fuel tap used on three and four cylinder models, used on Atlantic E2NN9N024AA.
$2.93
-
11033900
CONTROL CABLE
55-3/4" long. Control cable for diesel and gas applications.
$10.02
- Found on Diagram:
Hydraulic & Power Steering
-
11011005
POWER STEERING SEAL K
Power steering pump seal repair kit. Services Atlantic E6NN3K514EA99M, E6NN3K514AB, E0NN3K514AB pumps.
$11.68
-
-
11011007
AP S PUMP SEAL KIT
Power steering seal kit for units w/vertical resevoir fluid tank, January 1965 to August 1968.
$54.08
-
11011008
HYDRAULIC PUMP SEAL
Power steering pump front drive gear shaft seal. .64" (16.2mm) ID, 1.02: (28.83mm) OD, .25" (6.35mm width.
$3.22
-
11011009
PUMP REPAIR KIT
Minor repair kit for units w/cast-iron piston type pump. For models w/o IPTO only. Not compatible w/NCA600C or NCA600F pumps.
$38.92
-
11011012
HYDRAULIC PUMP
Capacity is 9.5 GPM at 2400 RPM (7.1 GPM at 1800 RPM), 2400 PSI Maximum Pressure. Will not replace piston type pump, gear type only. Requires mounting gasket E4NN911AA, not included. 2-4000 MODELS (3 CYL ONLY).
$511.46
-
11011020
HYDRAULIC PUMP
Small Pump, Gear style unit, center mounted, W/ Independent PTO, W/ Hydraulic Lift. Without Syncro trans, for 8x2 trans.
$654.53
-
11011028
POWER STEERING PUMP
Rated Pressure 725-1305 at 500-2000rpm. Safety valve Opening Pressure 942-1087 PSI,Safety Valve Full Open: 1087-1305 PSI. Unit designed for 'O' ring fitting, not supplied w/pump. This pump fits tractors with JIC fittings.
$529.99
-
-
-
-
-
-
-
-
-
-
-
-
-
-
11011163
HYDRAULIC PUMP SHAFT
Rubber reinforced seal with inside diameter of .935", outside diameter 2" and width .530".
$3.69
-
-
-
-
11011703
STEERING CYLINDER
Cylinder with 5/8" Rod (LH/RH). Early style cylinder with D8NN3A304AA female fittings. Can replace original cylinders with 1/2" rod.
$393.56
-
-
11011705
STEERING CYLINDER
Cylinder with 5/8" Rod (LH/RH). Late style cylinder with 265235 male fittings.
$393.56
-
11017000
HYDRAULIC OIL COOLER
Aluminum type trans/hydraulic oil cooler. 1/2" inlet and outlet. Interior tube 3/4" w/10 fins per inch. Dimensions are 10 3/4" by 4" by 1 1/2."
$143.61
- Found on Diagram:
Rear Axle
-
-
-
-
11057000
RR AXLE SHAFT BEARING
Bearing spacer only, w/ or w/o differential lock. Does not include roller bearing or race. Collar, ID: 3.22", OD: 3.45", W: 1.21".
$32.41
-