JavaScript Disabled - Unable to show Cart
There are (109) parts used by this model.
- Found on Diagram:
Brake
-
-
11022005
SPRING
Brake shoe adjusting screw spring
$5.41
-
11022006
SPRING
Brake shoe retracting spring, 1955 to 1964 four cylinder models.
$21.57
-
11022008
BRAKE SPRING KIT
Brake Shoe Spring & Retainer Kit (does not include brake shoes). Contains: 1 8N2048 socket, 4 6H2066 brake spring cup, 2 NCA2204A spring, 1 NCA2217A dust seal, 1 NCA2296B spring, 2 NCA2333A pin, 2 NCA22219A spring, 2 NCA22275A spring, 2 NCA22276A pin, 2 NCA22218A collar, 2 NCA22286A retainer, 1 H204
$81.18
- Found on Diagram:
Clutch, Transmission & PTO
-
-
-
-
11126003
PTO SNAP RING
1 3/8" outside diameter. PTO snap ring for diesel and gas applications.
$4.42
-
11126004
BEARING
PTO shifter bearing for diesel and gas applications. ID: 1.38:, OD:2.84", W: 0.67"
$11.68
-
11126009
PILOT BEARING
ID: 0.66" (16.992mm), OD: 1.57" (40.005mm), W: 0.47" (11.988mm), double seal.
$5.24
-
-
-
11126628
SEAL
Single Lip Oil seal, transmission drive gear, trans input shaft, also for combination trans Step Up/Down. ID: 1.375" (34.93mm), OD: 2.004" (50.9mm), W: 0.328" (8.33mm)
$6.39
-
12126007
CLUTCH DISC
Friction Disc, ID: 3.65" (92.7mm) w/ 45 teeth, OD: 5.24" (133.1mm), Ht: .0629" (1.6mm)
$23.61
- Found on Diagram:
Cooling
-
-
11066209
WATER PUMP
Single v-groove pulley, w/gasket. Fits gas and diesel models 1955~64.
$88.92
-
-
-
11066303
RADIATOR
Eight (8) fins per inch. Core is 17-1/2" tall, 15-1/4" wide, 2-1/4" thick. W/cap. Copper core.
$329.36
-
-
12060156
INLET HOSE
ID: 2"(50MM) L: 2.375" (60.00mm), OD: 2.4" (60.97mm)
$7.17
- Found on Diagram:
Electrical
-
11000121
STARTER
6/12v, DD, CW rotation. Uses NCA11450A solenoid and 1CM11350A drive. WARNING: Failure to disengage starter drive from flywheel prior to push starting tractor will result in damage to starter drive, starter, and flywheel. Do not spin starter drive by hand. Warranty does not cover bent armature, broke
$158.13
-
11000121D
STARTER W/DRIVE
6 VOLT ONLY, DD, CW rotation. 1CM11350C drive installed. Uses NCA11450A solenoid. FOR 12 VOLT VERSION USE 1100-0123D. WARNING: Failure to disengage starter drive from flywheel prior to push starting tractor will result in damage to starter drive, starter, and flywheel. Do not spin starter drive by h
$189.08
-
11000123D
STARTER W/DRIVE
12v, DD, CW rotation. 1CM11350C drive installed. Uses 311006 solenoid. WARNING: Failure to disengage starter drive from flywheel prior to push starting tractor will result in damage to starter drive, starter, and flywheel. Do not spin starter drive by hand. Warranty does not cover bent armature, bro
$177.64
-
-
-
-
11000307
STARTER DRIVE
9 tooth, CCW, 29 spline, 15.9mm ID, 123-140mm L, pin mount, 21.5mm pinion length. Locking barrel-folo design. WARNING: Failure to disengage starter drive from flywheel prior to push starting tractor will result in damage to starter drive, starter, and flywheel. Do not spin starter drive by hand. War
$42.01
-
11000540
COIL
6v (w/o resistor) or 12v (w/resistor), oil filled. Includes bracket and resisitor.
$18.96
-
11000559
REGULATOR
6v, 7.1 volt set, B-circuit, pos ground, Arm-Fld Bat terminals. GFD6001
$40.65
-
11000565
REGULATOR
12v, 14.5 Volt set. B Circuit, Neg (-) or Pos (+) ground. Terminals are ARM - FIELD - BAT.
$51.48
-
-
-
11000906
BULB
14v maximum, 3.8 watt, miniature bayonet base. Priced individually, sold in multiples of 10. Bulb for diesel and gas applications. Type 1895.
$1.07
-
11000912
BULB
12v, 4.3 watts, miniature bayonet base. Priced individually but sold in multiples of 10. Type 1816.
$0.44
-
11000951
IGNITION KEY
Spare key. For 8N3679C. Priced individually but sold in multiples of 2.
$1.09
-
11000958
STARTER SWITCH
8N 1948-52 w/o Selct-O-Matic. 1953-1964 other models listed. Uses 3/4" by 16 pitch nut.
$19.40
-
-
11000971
LIGHT SWITCH
6-12v, two screw terminal connectors, requires mounting hole of minimum 1/2".
$8.65
-
11006005
REAR LAMP LENS
Red Lens, tail light / brake light lens, fits original style housing.
$24.29
-
11006015
HEADLAMP
Headlight assembly, 12 volt sealed beam
$60.58
-
- Found on Diagram:
Engine
-
11091322
VALVE SPRING
Spring, intake and exhaust valve (8 used per engine)
$3.52
-
11095501
BELT
1/2" (13 mm) x 41 1/2" (1054 mm) raw edge v-belt.
$9.09
-
11099416
EXHAUST GASKET KIT
Kit includes (2) C0NN9448C manifold gaskets and (2) NAA55232A muffler gaskets
$4.91
-
-
-
-
-
-
11099911
EXHAUST MANIFOLD
Intake-Exhaust Manifold, with gaskets. Carb mount flange has slotted holes for use with various carbs.
$126.27
-
11099911KIT
MANIFOLD KIT
Kit includes manifold, exhaust gasket kit and manifold nut kit.
$147.48
-
- Found on Diagram:
Filters
-
-
FF3000
Fuel Filter
Fuel filter for diesel and gas applications.
$3.66
-
OF3101
LUBE FILTER
Features: Anti-Drainback Valve, By-Pass Valve. Lube filter for diesel and gas applications.
$5.75
-
OF3769
LUBE FILTER
Dimensions: ID: 1.02" / 26mm, OD: 2.99" / 76mm, Length: 1.61" / 41mm. Lube filter for diesel and gas applications.
$3.32
- Found on Diagram:
Front Axle & Steering
-
-
-
-
11044108
STEERING SHAFT
Ball Nut and Shaft assembly (w/ pwr steering). LOA: 23 3/4", 36 spline, 11/16" 20 UNF thread.
$368.50
-
-
11044900
STEERING WHEEL
18" Diameter center hub is 0.785 in, 36 splines. Steering wheel for diesel and gas applications.
$42.25
-
11044902
RADIUS BALL CAP
Radius ball cap used w/C5NN3N442C socket. Can be used for LH or RH side. Radius ball cap for diesel and gas applications.
$17.77
-
11044903
RADIUS SPACER
Radius rod socket, used w/ 83924040 cap. Can be used for LH or RH side.
$21.01
- Found on Diagram:
Fuel
-
11030051
CARB FLOAT
Brass material float chambers. W/o pin.
$12.25
-
-
11033381
O RING SEAL
Sold in Packs of 2 but priced individually. 3/8" fiber washer for Banjo Bolt 3133382 or 86531362.
$0.70
-
11033382
O RING SEAL
Sold in Packs of 2 but priced individually. 7/16" fiber washer for Banjo Bolt C0NN9A349B.
$1.07
-
-
-
11033393
GLASS BOWL
Glass Sediment Bowl for 311272 and CONN9155A Fuel Strainer Assemblies. 1 1/2" diameter bottom and 1 7/8" Long.
$11.25
-
11033394
SEDIMENT BOWL
For 134 CID gasoline motors, mounts to carburetor w/3/8" opening. Top lip of bowl 1-1/2" OD. Comes with Glass bowl not plastic.
$36.94
-
11033395
SEDIMENT BOWL
For models listed 1960~65, 7/16" opening, mounted to carburetor.
$34.97
-
11033396
GASKET
Contains one (1) seal and one (1) mesh material filter screen. Fits 1103-3394 and 1103-3395.
$2.35
-
11033398
FUEL TAP
Tank mounted fuel tap w/thumb screw. Uses .25" fuel line connector. Comes with o-ring. Mounting screw (2 required) type is #12 by 24 pitch, 3/4" length, not included.
$36.83
-
11033399
FUEL TAP
Tank mounted fuel tap w/lever. Includes 'o'-ring.
$41.16
-
-
11033402
FUEL CAP
Fuel cap for self venting tanks. Cap is non-vented. For vented cap use C5NN9030B.
$9.06
-
11033431
FUEL LINE
1/4" For Tractors with 134 CU. IN Engine. 1/2" x 20 pitch fittings.
$45.03
-
11033432
FUEL LINE
5/16" Fuel Line for Tractors with 172 CU. IN Engine.
$34.01
- Found on Diagram:
Gauges, Instruments, Cables
-
11070003
TACH CABLE
Vinyl cased tachometer cable, 48" length, for diesel and gas applications and models w/o cab.
$14.50
-
-
-
-
11072707
TACHOMETER
Tach, Proofmeter, CCW rotation, models with 10 speed transmission, '59 - '64 (will not replace C3NN17635A for Offset models or NAA)
$59.61
- Found on Diagram:
Hitch and Implement
-
11131071
CHECK CHAIN KIT
Drawbar check chain kit includes: RH/LH anchors, 2 eyelets, 2 chains, 4 clevis with pins and hdw
$41.07
- Found on Diagram:
Hydraulic & Power Steering
-
-
11010401
PUMP DRIVE COUPLER
Pump Drive Coupler. OD: 4", 4 mounting holes 7/16" diameter, 2 3/4" spacing, 1" x 10 spline hub.
$54.08
-
-
-
-
-
-
-
-
11011163
HYDRAULIC PUMP SHAFT
Rubber reinforced seal with inside diameter of .935", outside diameter 2" and width .530".
$3.69
-
-
- Found on Diagram:
Manuals & Decals
-
- Found on Diagram:
Rear Axle
-
- Found on Diagram:
Seats
-
- Found on Diagram:
Sheet Metal and Grille
-
11111461
TOOL BOX
Tool box is fender mounted. May need to be painted for color matching.
$49.30
-
11112000
TOOL BOX
15" long 4 1/2" width and height. May need to be painted for color matching.
$43.24
-
11116554
EMBLEM
Hood Emblem. EXACT of ORIGINAL (with metal back).
$75.77
- Found on Diagram:
Wheels, Hubs
-
11080001
No Longer Available
-
11080002
WHEEL STUD
1/2"-20 pitch with 1-1/8" usable thread, 2" overall shaft length. Wheel stud for diesel and gas applications. SOLD IN QUANTITIES OF 6.
$1.18
-
11084042
BEARING CONE CUP
Inner wheel bearing and race 4000, ref #'s 86516467/86516468. ID: 0.75", OD: 1.78", WOA: 0.61".
$10.54
-
11084063
HUB
Bare Hub Only. Requires NH Ref# 312520 and 5127125 bearings, not included. Hub for diesel and gas applications.
$75.88