JavaScript Disabled - Unable to show Cart
There are (303) parts used by this model.
- Found on Diagram:
Air Conditioning
-
- Found on Diagram:
Bearing
-
30200009
BEARING
Ball Bearing, ID: 1.378" (35mm), OD: 3.149" (80mm), W: 0.827" (21mm)
$51.92
- Found on Diagram:
Brake
-
-
-
-
11022900
BRAKE DUST SEAL
Ozone resistant material, steel base. Brake dust seal for diesel and gas applications.
$4.94
-
11022901
No Longer Available
-
11025503
BRAKE DISC
OD is 8.07", ID is 2.10", 22 teeth. 0.750" Facing, Brake disc for diesel and gas applications.
$40.43
-
11025507
BRAKE DISC
OD 8.22", ID 4.48", one notched oblong end. Brake disc for diesel and gas applications.
$8.73
-
11025516
FRICTION DISC
8" diameter, 22 tooth inside spline disc, 1.125" Facing
$40.18
- Found on Diagram:
Clutch, Transmission & PTO
-
11120010
PTO SHAFT
29.46" length , 10 spline w/ (1 1/4" od) x 6 spline w/ (1 1/2"od).
$104.17
-
-
11125046
SHIFT ARM
Short Hi-Low Range selector shaft w/pin on RH side. Shift arm for diesel and gas applications.
$51.45
-
11125505
CLUTCH PLATE
5.47" outside diameter by 3.90" inside diameter by 0.068" width, 54 tooth. PTO plate for diesel and gas applications.
$6.56
-
-
-
-
-
11126003
PTO SNAP RING
1 3/8" outside diameter. PTO snap ring for diesel and gas applications.
$4.42
-
11126004
BEARING
PTO shifter bearing for diesel and gas applications. ID: 1.38:, OD:2.84", W: 0.67"
$11.68
-
-
-
-
11126009
PILOT BEARING
ID: 0.66" (16.992mm), OD: 1.57" (40.005mm), W: 0.47" (11.988mm), double seal.
$5.24
-
11126011
No Longer Available
-
11126012
GASKET
Gasket, main drive gear retainer
$1.09
-
-
-
-
11126017
RELEASE BEARING
ID 2.49", OD 4.06", WOA 0.82", sealed roller. For mechanical release systems.
$30.20
-
-
11126025
CLUTCH DISC
13", 10 spline rigid disc, 1" hub, fiber type material.
$128.51
-
11126026
CLUTCH DISC
13", 10 spline, 1" hub w/damper springs, fiber type material.
$114.59
-
11126036
CLUTCH PLATE
13" pressure plate assembly w/29 spline 1 7/8" IPTO hub. Four finger w/ring.
$306.45
-
-
11126043
CLUTCH PLATE
This pressure plate replaces the original 3 finger design. 11" w/29 spline IPTO hub. Replaces three finger type. Note, for 4000 series with 8 bolts use C5NN7563U for correct mounting bolt pattern. This unit replaces 6 bolt Plate.
$284.45
-
11126044
CLUTCH DISC
11", 10 spline rigid, 1" hub, fiber type material.
$120.52
-
11126045
SHIFT ARM
Gear change lever used for cast iron base shift towers. Uses notch on RH side of lever as viewed from operators platform facing forward.
$49.03
-
11126046
SHIFT ARM
13 1/4" length main gear lever for units produced from 4/68 to 4/69 only. Uses notch on LH side of lever as viewed from operators platform facing forward.
$46.68
-
-
-
-
11126054
No Longer Available
-
-
11126057
PTO RR SHAFT SEAL
1939 thru 1964 with 1-1/8" or 1-3/8" PTO shaft. Seal is 2.45" O.D., 1 5/8" I.D., 5/8" wide. Fits 1965~ as well w/same measurements on shaft.
$5.18
-
-
11126090
CLUTCH KIT
Kit contains 11" 10 spline rigid drive disc E5NN7550BA, 11" 29 spline double pressure plate D8NN7502AA , pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool.
$542.52
-
11126113
CLUTCH KIT
Kit contains 11" 10 spline three pad triangular type drive disc C7NN7550AC, 11" 29 spline IPTO hub pressure plate with four finger design that will also replace three finger type with six (6) bolt mounting design D8NN7563DB, release bearing 83914247, pilot bearing C5NN7600A, and 1" by 10 spline and
$390.70
-
11126120
CLUTCH KIT
Kit contains 11" 10 spline rigid drive disc87295808, 11" 29 spline IPTO pressure plate D8NN7563DB, pilot bearing C5NN7600A and release bearing 83914247 , includes pilot tool.
$379.83
-
11126131
CLUTCH KIT
Kit contains 11" 15 spline spring drive disc E8NN7550AA, 11" IPTO 29 spline pressure plate D8NN7563DB, pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool. This is the 6 bolt pressure plate version and will not replace the 8 bolt version.
$431.29
-
11126163
CLUTCH KIT
Kit contains 13" 10 spline spring drive disc with 1" hub E7NN7550BB, 13" 29 spline IPTO pressure plate C5NN7563AC, pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool.
$417.01
-
11126164
CLUTCH KIT
Kit contains 13" 10 spline rigid drive disc with 1" hub F0NN7550BA 13" 29 spline IPTO pressure plate C5NN7563AC, pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool.
$417.25
-
11126191
CLUTCH KIT
LuK RepSet®, clutch kit, includes 13" (330mm), 8 bolt, pressed steel, diaphragm spring, fixed 1 7/8"-29 spline PTO hub, single pressure plate, 10 spline dampened organic disc, 100mm OD, 63.5mm ID release bearing, 40mm OD, 17mm ID pilot bearing. For models w/ Non-Synchro Trans.
$850.50
-
11126193
CLUTCH KIT
LuK RepSet®, clutch kit, includes 13" (330mm), 8 bolt, pressed steel, diaphragm spring, fixed 1 7/8"-29 spline PTO hub, single pressure plate, 10 spline dampened organic disc, 100mm OD, 63.5mm ID release bearing, 40mm OD, 17mm ID pilot bearing. For models w/ Synchro Trans.
$974.83
- Found on Diagram:
Cooling
-
-
11066110
RADIATOR CAP
Radiator Cap rated for 13 psi. Overflow reservoir systems, 3/4" neck
$6.04
-
-
11066200
WATER PUMP
Front pump only, single groove v-belt pulley. Mounting holes 5/16" and 7/16" and will replace earlier units w/smaller mounting holes. Includes both pump and housing gaskets (Atlantic #E6NN8513AA and E5NN8507AB).
$64.58
-
11066201
WATER PUMP
Front pump only, double groove v-belt pulley. Includes both pump and housing gaskets (Atlantic #E5NN8507AB).
$114.77
-
11066204
WATER PUMP
Single pulley hub for bolt on fan, complete pump including back plate. For models w/o heater plug or cab heater.
$95.27
-
-
-
11066294
RADIATOR HOSE
Upper Radiator Hose 1 1/2" I.D. for Gasoline Models.
$13.64
-
11066297
FAN SHROUD
Fiberglass type must drill holes for proper fitment.
$85.36
-
-
-
-
-
-
11066310
RADIATOR HOSE
1.5" inside diameter, upper hose for Diesel models.
$6.34
-
- Found on Diagram:
Electrical
-
11000100
5IN DIESEL STARTER
OE Lucas unit. DD, 2.8KW, 12v, 10 tooth drive. Uses D2NN11390A solenoid. Uses E4NN11350AA drive. Starter for Ford/New Holland diesel applications.
$246.79
-
11000100A
STARTER, AFTERMARKET
12v, 10 tooth, 2.8KW. Aftermarket unit, not OE Lucas, as 83981923. Uses D7NN11390B Atlantic solenoid and C5NF11350C Atlantic drive. Note: Warranty is six (6) months from date of purchase, unit replacement only. Starter for Ford/New Holland diesel applications.
$217.22
-
11000105
STARTER
Gear reduction option for D8NN11000CE. Starter for Ford/New Holland diesel applications.
$235.95
-
11000112
STARTER
12v, 10 tooth, DD unit. Uses C5NF-11A108-A drive. Uses D2AF11450A solenoid. For 3 Cylinder Gas.
$190.64
-
-
-
-
-
11000301
STARTER DRIVE
For 4.5"Lucas (M45), 10 tooth, CW, fits 12spline armature, 17mmID, 40mmGr, 70mmL, 60mmOD.
$58.42
-
11000302
STARTER DRIVE
10 tooth, CW, fits 12spline armature, 17mmID, 40mmGr, 73mmL, 60mmOD.
$53.66
-
11000410
BATTERY CABLE
34" Length. Negative battery cable for diesel and gas applications.
$24.30
-
11000411
BATTERY CABLE
36-1/2" Length. Positive battery cable for diesel and gas applications.
$34.56
-
11000500
ALTERNATOR
70 amp unit w/battery sensor. D+, D+, B+ and W terminals. Has 'Lucor' connector as well under plastic terminal protector.
$166.80
-
110005004
ALTERNATOR
12v, 45a, IR, EF, clockwise, Lucas replacement
$157.26
-
-
11000540
COIL
6v (w/o resistor) or 12v (w/resistor), oil filled. Includes bracket and resisitor.
$18.96
-
11000550
REGULATOR
12v, 14.1 volt set, Four prong (two male-two female) connector for Motorolla style alternators w/external regulator. Fits ref#'s D5NN10300D and D5NN10300E. If regulator is not used with correct alternator, unit will not charge. Non-adjustable.
$38.92
-
11000553
REGULATOR
12v, 14.4 volt set, A-circuit, W/battery temp sensor. Fits ref#'s E7NN10B376AB, BB, E3NN10B376AD (Atlantic 81863039, 81863039, 81868798). Fits Lucas/Marelli units.
$43.24
-
11000560
REGULATOR
12v, round terminal plug with four male connectors. Fits units w/Motorolla equipped.
$79.73
-
-
-
11000906
BULB
14v maximum, 3.8 watt, miniature bayonet base. Priced individually, sold in multiples of 10. Bulb for diesel and gas applications. Type 1895.
$1.07
-
11000909
BULB
12v, 27/8.3 watt, double bayonet base. Type 1157. Priced individually, sold in multiples of 10.
$0.63
-
11000914
BULB
12v, halogen, single spade halogen collar base. Type H1-55.
$6.49
-
11000915
BULB
12v, 60/55 watt, P43T base. Bulb for diesel and gas applications. Type H4-60P43.
$6.49
-
11000916
BULB
12v, 55 watt, PK22S base. Bulb for diesel and gas applications. Type H3-55.
$4.88
-
11000918
BULB
12v, 1.70 watts, miniature bayonet base. Priced individually, sold in multiples of 10. Type 53.
$1.72
-
11000933
FUSE
AGC15 fuse for diesel or gas applications, Priced Individually, Sold in Multiples of 5
$0.30
-
11000950
DIESEL STARTER BUSHIN
17.10mm ID, 21.04mm OD, 22.10mm L. Sintered brass material. Starter bushing for diesel applications.
$2.35
-
11000960
IGNITION SWITCH
Seven terminal Lucas type with cold start. Rated at max 35 amp load. Ignition switch for diesel and gas applications.
$13.34
-
11000968
IGNITION KEY
Priced individually, sold in multiples of 2. Ignition key for diesel and gas applications.
$1.91
-
11000969
STOP LIGHT SWITCH
12V Stop Light Switch for diesel and gas applications. Two connectors.
$29.24
-
-
11000978
LIGHT SWITCH
Fits numerous 1965~, 3-4-6 cyl's, rotary type switch. Light switch for diesel and gas applications.
$14.63
-
11000984
HOLD DOWN W/ NUT
1965~, 7" L by 5/16"x18 thread pitch. Battery Hold Down with nut for diesel and gas applications.
$3.66
-
-
11006005
REAR LAMP LENS
Red Lens, tail light / brake light lens, fits original style housing.
$24.29
-
11006015
HEADLAMP
Headlight assembly, 12 volt sealed beam
$60.58
-
12000100
STARTER
12v, 10 tooth, 2.8KW, Direct Drive, LH mount. Uses 1200-0200 solenoid and 1200-0300 drive. 3.50" CTC mount. Note, on some MF175 models using Delco 20MT #1107872 or 1109261 use Delco type 28MT 6630180. Starter for diesel applications.
$270.85
-
12000203
SOLENOID
12v, three terminal, switch terminal is male spade. For Lucas and Marelli units.
$45.20
- Found on Diagram:
Engine
-
-
-
11091022
CONROD BOLT
Conrod bolt for diesel and gas applications.
$4.50
-
11091023
CONROD NUT
Conrod nut for diesel and gas applications.
$1.12
-
11091031
LINER
Top Flanged Sleeve with inside diameter of 4.4", outside diameter 4.50", Flange lip .10", diameter at flange 4.738" and overall length is 8.21". Semi Finished Liner for diesel applications.
$50.34
-
11091033
OVERSIZE LINER
Length 8.21", I.D. 4.4" and O.D. 4.6" Semi Finished Liner
$46.71
-
11091040
VALVE TRAIN KIT
Valve train kit consists of intake and exhaust valves, springs, keepers and valve seals. Valve train kit for diesel 3 cyl engine applications.
$119.20
-
-
-
-
-
-
-
-
-
-
11091172
ROD BEARINGS .020
0.020" Oversize rod bearings for diesel and gas 3 cylinder applications.
$35.12
-
-
-
-
11091270
CAMSHAFT
Camshaft for diesel applications.
$269.12
-
11091271
CAMSHAFT BUSHING
Camshaft bushing for diesel and gas applications. Four used in three cylinder applications, five used in four and six cylinder applications.
$7.61
-
11091306
SPRING
Valve spring for diesel applications.
$10.43
-
11091307
SPRING
Valve spring for diesel applications.
$4.50
-
11091308
COTTER KEEPERS
Cotter keepers for diesel applications. Priced individually, Sold Individually.
$1.28
-
-
-
-
-
11095502
BELT
1/2" (13 mm) x 55 7/16" (1408 mm) raw edge v-belt.
$8.65
-
-
-
-
-
11099404
OIL PAN
Stamped steel construction.
$116.94
-
-
-
11099409
OIL CAP
Plug type cap, screw in to tighten.
$13.23
-
-
-
-
11099450
PRE CLEANER
For 3" pipe inlet, 10" outside diameter of cap.
$46.71
-
-
11099501
AIR CLEANER BOWL
For units using 3" to 4" inlet pipes. 10" outside diameter, 3 5/8" inside diameter, outer height 2 3/4", center cone 4" height. Can be used w/86011276 assembly.
$11.22
-
-
-
11099524
PRE CLEANER
Air intake cap for 2 1/4" pipe, black in color.
$15.11
-
-
11099901
MANIFOLD
Three (3) cylinder horizontal exhaust manifold. Uses Atlantic E8NN9448AA exhaust gasket.
$74.92
-
-
- Found on Diagram:
Filters
-
AF2614
AIR FILTER
This filter is currently available in Baldwin brand. Air filter for diesel and gas applications.
$77.28
-
AF2615
AIR FILTER
Air filter for diesel and gas applications.
$48.68
-
FF3000
Fuel Filter
Fuel filter for diesel and gas applications.
$3.66
-
HF4431
LUBE FILTER
Dimensions: OD: 3.7" (94mm), Length: 6.93" (168mm), Thread: 1.125" x 16 UNF, Features: By-Pass Valve. Lube filter for diesel and gas applications.
$11.90
-
HF9100
LUBE FILTER
Lube filter for diesel and gas applications.
$11.87
-
OF3101
LUBE FILTER
Features: Anti-Drainback Valve, By-Pass Valve. Lube filter for diesel and gas applications.
$5.75
- Found on Diagram:
Front Axle & Steering
-
11044008
SPINDLE BEARING
ID is 1.345", OD is 2.2", Width is .622". Spindle bearing for diesel and gas applications.
$6.61
-
11044018
SPINDLE BUSHING
Height 1.482", OD 1.380", ID 1.25" Spindle bushing for diesel and gas applications.
$4.75
-
11044019
LINK END ASSEMBLY
Front side, 4" center to end, .687" shaft diameter w/18 pitch LH thread.
$14.85
-
11044020
LINK END ASSEMBLY
Rear angled shaft end 4 1/2" LOA, .687" diameter w/18 pitch RH thread.
$14.85
-
11044024
SPINDLE
RH, 11.687"L, 1.25" Upper diameter, 1.340" Lower diameter, 1.25" Inner stub diameter, .750" Outer stub diameter. Keyway is .235"W x .914"L.
$108.26
-
11044026
SPINDLE
LH, 11.687"L, 1.25" Upper diameter, 1.340" Lower diameter, 1.25" Inner stub diameter, .750" Outer stub diameter. Keyway is .235"W x .914"L.
$106.11
-
-
11044030
SPINDLE SEAL
OD: 1.71" (43.4mm), ID: 1.25" (31.8mm), W: 0.21" (5.3mm).
$1.99
-
11044033
AXLE BUSHING
Front axle bushing, 2.19" outside diameter, 2.05" inside diameter, 1.5" length, non-split design w/inner spiral relief for lubrication. Axle bushing for diesel and gas applications.
$5.40
-
-
-
-
11044047
SPINDLE BEARING
Spindle bearing for diesel and gas applications. Greasable, ID: 1.50", OD: 2.25", WOA: 0.78".
$9.31
-
11044048
DRAG LINK END
3/4" by 16 pitch LH threads, 9/16" pin. Drag link end for diesel and gas applications.
$22.52
-
-
-
11044064
STEERING NUT
Steering nut for diesel and gas applications. 11/16" x 24 pitch (NF)
$6.39
-
-
-
-
-
11044087
STEERING SHAFT
Ball Nut and Shaft assembly. LOA: 26.57" (675mm), 36 spline, 11/16" 20 UNF thread.
$362.00
-
11044111
SPINDLE
Spindle for diesel and gas applications. RH
$136.46
-
11044112
SPINDLE
Spindle for diesel and gas applications. LH
$136.46
-
11044170
SEAL
Spindle dust seal with seal with groove and offset rubber for steering arm. OD: 1.71" (43.4mm), ID: 1.25" (31.8mm), W: 0.21" (5.3mm).
$2.13
-
-
-
11044184
DRAG LINK
Tube Length 28.125" (714.375mm), Overall length 30.10" (790mm)
$135.15
-
-
11044211
FRONT AXLE
Front Axle Center section, includes C7NN3153B bushing
$242.67
-
11044401
STEERING ARM
Spindle steering arm, for manual and power steering models, replaces 957E3130.
$57.93
-
11044450
STEERING GEAR ASSEMBL
Manual steering gear w/18" mainshaft. Sector shafts use D9NN2N289AA seals, already installed. Steering gear assembly for diesel and gas applications.
$648.12
-
11044554
TIE ROD
Outer tie rod end, right hand, thread ID: 3/4-16 UNF, usable length: 4.34" (110.24mm). Fits cab models built 4/1/1976 and later. (10 Series, 234, 334 and 335 British built only)
$78.78
-
11044900
STEERING WHEEL
18" Diameter center hub is 0.785 in, 36 splines. Steering wheel for diesel and gas applications.
$42.25
-
-
11044902
RADIUS BALL CAP
Radius ball cap used w/C5NN3N442C socket. Can be used for LH or RH side. Radius ball cap for diesel and gas applications.
$17.77
-
11044903
RADIUS SPACER
Radius rod socket, used w/ 83924040 cap. Can be used for LH or RH side.
$21.01
-
11044906
STEERING WHEEL
36 Spline inner hub, 15" Outer rim diameter, PVC grained cover material. Steering wheel for diesel and gas applications.
$49.03
-
-
11045218
BEARING CUP
Tapered Cup OD: 2.33" (59.18mm), ID: 2.24" (11.68mm), W: 0.46"
$3.15
-
11047077
SEAL
Seal, steering shaft. For 2-wheel drive models. OD: 1.39" (35.31mm), ID: 0.87" (22.09mm), W: 0.37" (9.39mm)
$9.12
-
- Found on Diagram:
Fuel
-
-
-
-
11033199
INJECTOR SEAL KIT
For all FNH 'long body' type injectors. Includes cork dust seal, copper compression seal and 2 aluminum return line seals.
$2.81
-
11033200
INJECTOR
Does not include washers, order 1103-3199 seal kit for washers and cork seal. Open Pressure 200-216.
$77.24
-
-
-
11033400
FUEL TANK
13 gallons (49.2 litres), for units equipped w/lock ring fuel sender. Fill neck height 2". Note: Will not fit 4000 models. Does not include lock ring or fuel tap. Does include fuel cap.
$193.34
-
-
-
11033404
FUEL SENDER
For fuel tanks using lock ring design sending unit. Fits Atlantic E3NN9002AB. Fuel sender for diesel applications.
$56.89
-
11033407
FUEL TAP
Tank tap is 7/8" tapered by 14 pitch, fuel line is 1/2" by 20 pitch.
$14.20
-
11033408
FUEL BOWL
Flat bottom type. Fuel bowl for diesel applications with 1" bottom hole.
$6.78
-
11033409
FUEL TANK
Original style Lock Ring Fuel Tank, for tractors equipped with lock ring type sender, does not include gasket, lock ring, fuel cap or fuel tap. Can replace E3NN9002KB fuel tank if D8NN9A316KA sender, E2NN1276AA gasket and C5NN9N283A twist lock are used.
$238.33
-
11033411
FUEL TAP SCREEN
Replaceable plastic fuel screen filter for fuel tap used on three and four cylinder models, used on Atlantic E2NN9N024AA.
$2.93
-
11033900
CONTROL CABLE
55-3/4" long. Control cable for diesel and gas applications.
$10.02
- Found on Diagram:
Gauges, Instruments, Cables
-
11070001
CABLE
Brass material, 4-1/4" length. Cable for diesel and gas applications. With alternator.
$7.01
-
11070003
TACH CABLE
Vinyl cased tachometer cable, 48" length, for diesel and gas applications and models w/o cab.
$14.50
-
11072701
GAUGE CLUSTER
CCW tach rotation. Does not include harness. Gauge cluster for diesel and gas applications.
$187.18
-
11072705
GAUGE CLUSTER
For models w/mechanical tach. Gauge cluster assembly for diesel and gas applications.
$257.41
- Found on Diagram:
Hitch and Implement
-
11130500
LEVELING BOX
Adjusts from 27 1/4" to 32 1/4". Fork is 21"L. Cat I. Top knuckle 5/8" ID, Lower fork 3/4" ID.
$95.27
-
-
11130517
TOP LINK END
Top Link End, CAT II, 1 1/4" LH Thread, 1" Ball ID, OAL 13"
$48.47
-
-
-
-
11132005
STABILIZER ASSEMBLY
W/pin, shackle, and coupling. W/o brackets and U bolts. Adjust from 17" to 23 1/2".
$95.27
-
11132006
SWINGING DRAWBAR
LOA: 32 1/2", W: 2", Thickness: 1", Offset: 1". Includes Drawbar Clevis Kit DJPN825A
$129.95
-
11132007
TOP LINK
Category II OE style toplink, with lever lock, collapsed length apx. 27".
$72.60
-
-
-
- Found on Diagram:
Hydraulic & Power Steering
-
-
-
11011005
POWER STEERING SEAL K
Power steering pump seal repair kit. Services Atlantic E6NN3K514EA99M, E6NN3K514AB, E0NN3K514AB pumps.
$11.68
-
-
11011008
HYDRAULIC PUMP SEAL
Power steering pump front drive gear shaft seal. .64" (16.2mm) ID, 1.02: (28.83mm) OD, .25" (6.35mm width.
$3.22
-
11011012
HYDRAULIC PUMP
Capacity is 9.5 GPM at 2400 RPM (7.1 GPM at 1800 RPM), 2400 PSI Maximum Pressure. Will not replace piston type pump, gear type only. Requires mounting gasket E4NN911AA, not included. 2-4000 MODELS (3 CYL ONLY).
$511.46
-
11011020
HYDRAULIC PUMP
Small Pump, Gear style unit, center mounted, W/ Independent PTO, W/ Hydraulic Lift. Without Syncro trans, for 8x2 trans.
$654.53
-
11011028
POWER STEERING PUMP
Rated Pressure 725-1305 at 500-2000rpm. Safety valve Opening Pressure 942-1087 PSI,Safety Valve Full Open: 1087-1305 PSI. Unit designed for 'O' ring fitting, not supplied w/pump. This pump fits tractors with JIC fittings.
$529.99
-
-
-
-
-
-
-
-
-
-
-
-
11011703
STEERING CYLINDER
Cylinder with 5/8" Rod (LH/RH). Early style cylinder with D8NN3A304AA female fittings. Can replace original cylinders with 1/2" rod.
$393.56
-
-
11011705
STEERING CYLINDER
Cylinder with 5/8" Rod (LH/RH). Late style cylinder with 265235 male fittings.
$393.56
-
11012003
HYDRAULIC VALVE
Single spool double acting hydraulic valve kit. Single spool. (Mounts on lift cover under the seat).
$411.74
-
11017000
HYDRAULIC OIL COOLER
Aluminum type trans/hydraulic oil cooler. 1/2" inlet and outlet. Interior tube 3/4" w/10 fins per inch. Dimensions are 10 3/4" by 4" by 1 1/2."
$143.61
- Found on Diagram:
Manuals & Decals
-
- Found on Diagram:
Muffler
-
11172209
MUFFLER
Vertical -Oval Body. Shell 4-1/2" x 9" Inlet size 1 7/8" with an outlet size of 2 ", length 41"
$146.07
-
11172300
MUFFLER
Vertical -Oval Body. Shell 4-1/2" x 9"
$147.99
- Found on Diagram:
Rear Axle
-
- Found on Diagram:
Seats
-
30100009
SEAT
Blue seat cushion and pan assembly with drain hole. For Deluxe Suspension Seat
$150.22
-
30100016
SEAT
Black seat cushion and pan assembly with drain hole. For Deluxe Suspension Seat
$150.22
- Found on Diagram:
Sheet Metal and Grille
-
11111461
TOOL BOX
Tool box is fender mounted. May need to be painted for color matching.
$49.30
-
-
11111550
FENDER SKIN
Rear fender skin without mounting bracket. Fender is for right or left side. Shipped with a protective primer finish allowing for a better match to exact paint scheme.
$110.44
-
11112000
TOOL BOX
15" long 4 1/2" width and height. May need to be painted for color matching.
$43.24
-
11112001
SUPPORT ROD
Support rod, 18.5" length, for diesel and gas applications.
$8.65
-
11112002
HOOD HANDLE
Hood handle for diesel and gas applications.
$8.22
-
-
-
11116000
BATTERY TRAY
Battery tray for diesel applications w/ 128 AH battery. Shipped with a protective primer finish allowing for a better match to exact paint scheme.
$88.11
-
11116547
BRACKET
For use with fenders D8NN16312AB and E5NN16313DA. Shipped with a protective primer finish allowing for a better match to exact paint scheme.
$129.95
-
11119001
GAS STRUT, REAR WINDO
Gas Spring (Window). LOA: 500mm, Stroke: 225mm, Force: 210N, Cyl Dia: 18mm, Rod Dia: 8mm. Ball and socket ends.
$21.57
-
11119003
GAS STRUT, DOOR
Gas Spring (Door). LOA: 505mm, Stroke: 205mm, Force: 220N, Cyl Dia: 18mm, Rod Dia: 8mm. Ball and socket ends.
$23.73
- Found on Diagram:
Wheels, Hubs
-
11080001
No Longer Available
-
11080002
WHEEL STUD
1/2"-20 pitch with 1-1/8" usable thread, 2" overall shaft length. Wheel stud for diesel and gas applications. SOLD IN QUANTITIES OF 6.
$1.18
-
11080003
WHEEL STUD
Width 3/4" with 16 pitch thread by 2-1/4" length. Wheel stud for diesel and gas applications.
$3.96
-
11080103
RIM STOP SCREW
Screw, for stop body. Use with power adjust rims PAR10X28, C5NN1050J, and C5NN1050H.
$4.66
-
11082000
DISC, WHEEL
Rear wheel 28"& 32", 8-bolt hub, 6-bolt rim
$315.93
-
11084001
FRONT HUB KIT
Kit contains 1 of 957E1139 dust cap, 1 of EHPN1200E wheel bearing kit, 6 of C5NN1012B wheel nuts. 6 of C5NN1107F wheel studs, and 1 of C9NN1104F hub.
$95.89
-
11084002
FRONT HUB KIT
Kit contains 1 of 957E1139 dust cap, 1 of EHPN1200C wheel bearing kit, 6 of C5NN1012B wheel nuts, 6 of C5NN1107F wheel studs, and 1 of C9NN1104E hub.
$95.40
-
-
11084006
DUST CAP
W/zerk tap, zerk fitting not included.
$7.01
-
11084007
TAB WASHER
OD 1.50" (38.20mm). ID .775" (19.70mm), Thickness 1/16"(1.23mm).
$0.90
-
-
-
11084042
BEARING CONE CUP
Inner wheel bearing and race 4000, ref #'s 86516467/86516468. ID: 0.75", OD: 1.78", WOA: 0.61".
$10.54
-
-
-
11088000
WHEEL BEARING KIT
Contians: Seal type TCM1682713, Outer Race Type LM11910, Outer Bearing type LM11949, Inner Race type LM67010, Inner Bearing type LM67048.
$18.02
-
11088001
WHEEL BEARING KIT
Contains: Seal, Outer Race Type LM11910, Outer Bearing type LM11949, Inner Race type LM48510, Inner Bearing type LM48548.
$22.83
-
30081010
RIM
16x5.5 width. 4 5/8" center ID. 6 Lug
$100.56
-
30081019
RIM
16x4.5, 4 5/8" Pilot, 6 Lug
$80.09