Ford 3600 Front Axle & Steering Parts Diagram

SPINDLE BEARING
ID is 1.345", OD is 2.2", Width is .622". Spindle bearing for diesel and gas applications.

SPINDLE BUSHING
: Height 1.482", OD 1.380", ID 1.25" Spindle bushing for diesel and gas applications.

LINK END ASSEMBLY
Front side, 4" center to end, .687" shaft diameter w/18 pitch LH thread.

LINK END ASSEMBLY
Rear angled shaft end 4 1/2" LOA, .687" diameter w/18 pitch RH thread.

SPINDLE
RH, 11.687"L, 1.25" Upper diameter, 1.340" Lower diameter, 1.25" Inner stub diameter, .750" Outer stub diameter. Keyway is .235"W x .914"L.

SPINDLE
LH, 11.687"L, 1.25" Upper diameter, 1.340" Lower diameter, 1.25" Inner stub diameter, .750" Outer stub diameter. Keyway is .235"W x .914"L.

SPINDLE SEAL
OD: 1.71" (43.4mm), ID: 1.25" (31.8mm), W: 0.21" (5.3mm).

AXLE BUSHING
Front axle bushing, 2.19" outside diameter, 2.05" inside diameter, 1.5" length, non-split design w/inner spiral relief for lubrication. Axle bushing for diesel and gas applications.

STEERING COLUMN BUSHI
Steering column bushing for diesel and gas applications.

STEERING SEAL FELT
Steering Seal Felt for diesel and gas applications.

STEERING BEARING RACE
Race only, Cylindrical type, ID: 1.33", OD: 1.76", W: 0.39".

SPINDLE BEARING
Spindle bearing for diesel and gas applications. Greasable, ID: 1.50", OD: 2.25", WOA: 0.78".

DRAG LINK END
3/4" by 16 pitch LH threads, 9/16" pin. Drag link end for diesel and gas applications.

PITMAN SHAFT SEAL

STEERING BEARING
Tapered roller bearing and race for steering shaft.

STEERING BEARING
Tapered roller bearing and race for steering shaft.

STEERING NUT
Steering nut for diesel and gas applications. 11/16" x 24 pitch (NF)

SPINDLE BUSHING
ID: 1.352", OD: 1.474", L: 1.490"

STEERING SHAFT
Manual steering shaft w/block asm., 26 1/4" length. Does not come with end nut for steering wheel.

SPINDLE BUSHING KIT
Kit contains (2) 2N3109 Spindle bushings, (2) NCA3110A Spindle bushings.

STEERING SHAFT
Ball Nut and Shaft assembly. LOA: 26.57" (675mm), 36 spline, 11/16" 20 UNF thread.

FRONT AXLE LH
Spindle Housing, Axle Knee LH

FRONT AXLE RH
Spindle Housing, Axle Knee RH

BALL JOINT
Ball joint has threaded end.

SEAL
Spindle dust seal with seal with groove and offset rubber for steering arm. OD: 1.71" (43.4mm), ID: 1.25" (31.8mm), W: 0.21" (5.3mm).

TIE ROD END
4.000", M20 X 1.5 LH Thread

DRAG LINK
29.625" Ctr Ball Joint to End

DRAG LINK
Tube Length 28.125" (714.375mm), Overall length 30.10" (790mm)

INNER TIE ROD
Replaces 83902604. 14.000", 0.750" ID

TIE ROD END
LOA: 4.00", Dia: M20 X 1.5 RH Thread

FRONT AXLE
Front Axle Center section, includes C7NN3153B bushing

STEERING ARM
Spindle steering arm, for manual and power steering models, replaces 957E3130.

TIE ROD
Outer tie rod end, right hand, thread ID: 3/4-16 UNF, usable length: 4.34" (110.24mm). Fits cab models built 4/1/1976 and later. (10 Series, 234, 334 and 335 British built only)

STEERING WHEEL
18" Diameter center hub is 0.785 in, 36 splines. Steering wheel for diesel and gas applications.

RADIUS BALL CAP
Radius ball cap used w/C5NN3N442C socket. Can be used for LH or RH side. Radius ball cap for diesel and gas applications.

RADIUS SPACER
Radius rod socket, used w/ 83924040 cap. Can be used for LH or RH side.

STEERING WHEEL
36 Spline inner hub, 15" Outer rim diameter, PVC grained cover material. Steering wheel for diesel and gas applications.

STEERING WHEEL CENTER

BEARING CUP
Tapered Cup OD: 2.33" (59.18mm), ID: 2.24" (11.68mm), W: 0.46"

SEAL
Seal, steering shaft. For 2-wheel drive models. OD: 1.39" (35.31mm), ID: 0.87" (22.09mm), W: 0.37" (9.39mm)

SPIDER JOINT