Ford 3600 Engine Parts Diagram

PISTON KIT
4.2" Piston, Piston Rings, Piston Clips and Piston Pin for diesel applications.

PISTON KIT 20 OVERSIZ
Piston kit for diesel applications.

PISTON KIT 30 OVERSIZ
Piston Kit for diesel applications.

PISTON KIT 40 OVERSIZ
Piston kit for diesel applications.

CONNECTING ROD
Connecting rod for diesel applications.

CONNECTING ROD BUSHIN
Connecting rod bushing for diesel applications.

CONROD BOLT
Conrod bolt for diesel and gas applications.

CONROD NUT
Conrod nut for diesel and gas applications.

LINER
Length 8.25", O.D 4.36" and I.D. 4.2". Semi Finished Liner for diesel applications.

VALVE TRAIN KIT
Valve train kit consists of intake and exhaust valves, springs, keepers and valve seals. Valve train kit for diesel 3 cyl engine applications.

MAIN BEARINGS STD
Standard size main bearings for diesel applications.

MAIN BEARINGS .010
Oversize main bearings (.010") for diesel applications.

PISTON RING KIT STD

PISTON RING KIT .020

PISTON RING KIT .030

PISTON RING KIT .040

PUSH ROD

INTERMEDIATE DRIVE SH
Oil pump intermediate drive shaft, for gas and diesel.

VALVE TAPPET

PISTON AND PIN ASSEMB

PISTON AND PIN ASSEMB

ROD BEARINGS STD
Standard size rod bearings for 3 cyl diesel engines.

ROD BEARINGS .010
0.010" Oversize rod bearings for 3 cyl diesel engines.

ROD BEARINGS .020
0.020" Oversize rod bearings for diesel and gas 3 cylinder applications.

ROD BEARINGS .030
0.030" Oversize rod bearings for 3 cyl diesel engines.

THRUST WASHER
Thrust washer for diesel applications.

HEAD GASKET SET
Head gasket set for diesel applications.

BOTTOM GASKET SET
Bottom gasket set for diesel applications.

HEAD GASKET
Head gasket for diesel applications.

CAMSHAFT
Camshaft for diesel applications.

CAMSHAFT BUSHING
Camshaft bushing for diesel and gas applications. Four used in three cylinder applications, five used in four and six cylinder applications.

INTAKE VALVE
Intake valve for diesel applications.

SPRING
Valve spring for diesel applications.

SPRING
Valve spring for diesel applications.

COTTER KEEPERS
Cotter keepers for diesel applications. Priced individually, Sold Individually.

EXHAUST V SEAL
Exhaust V Seal for diesel applications.

INLET V SEAL
Inlet V Seal for diesel applications.

EXHAUST V SEAL
Exhaust V seal for diesel applications.

RING GEAR
128 tooth ring gear.

BELT
1/2" (13 mm) x 55 7/16" (1408 mm) raw edge v-belt.

OIL PUMP

OIL PUMP SCREEN

FRONT CRANK SEAL
3 1/4" OD by 2 1/4" ID.

VALVE COVER GASKET
For three cylinder OHV motors, cork material.

OIL PAN
Stamped steel construction.

OIL PAN GASKET

DIPSTICK
7 1/2" gauge shaft length.

OIL CAP
Plug type cap, screw in to tighten.

RR CRANK SEAL
OD:141mm, ID: 120mm, W:11.3mm

MANIFOLD GASKET

MANIFOLD GASKET

DRAIN PLUG GASKET

AIR CLEANER BOWL
For units using 2 1/4" to 2 1/2" inlet pipes.

AIR CLEANER BOWL
For units using 3" to 4" inlet pipes. 10" outside diameter, 3 5/8" inside diameter, outer height 2 3/4", center cone 4" height. Can be used w/86011276 assembly.

OIL PRESSURE SWITCH
"T" connector will connect with standard female spade connector.

TEMP SENDER

AIR CLEANER
7" diameter. Oil Bath Air Cleaner.

AIR CLEANER ASSEMBLY
Six (6") oil bath design, complete unit.

AIR CLEANER ASSEMBLY (No Longer Available)
7.75" oil bath design, complete unit.

AIR CLEANER HOSE
Large end diameter is 2 1/2" and the small end is 2"

RAIN CAP
2" Rain Cap. For 2" OD pipe

PRE CLEANER
Air intake cap for 2" pipe, black in color.

PRE CLEANER
Air intake cap for 2 1/4" pipe, black in color.

TEMP SENDER
M18-1.5 thread with spade connector

TEMP SENDER
Temperature sender, water, for diesel and gas applications.

AIR CLEANER COVER
Air cleaner access cover.

MANIFOLD
Three (3) cylinder horizontal exhaust manifold. Uses Atlantic E8NN9448AA exhaust gasket.

EXHAUST MANIFOLD

EXHAUST PIPE

EXHAUST CLAMP
Exhaust clamp for diesel and gas applications.

ENGINE BASE KIT
Base Engine Kit: Includes standard pistons w/rings, complete gasket set with front and rear crank seals and connecting rod bushings. Rod or main bearings can be added separately. Please indicate the rod and main bearing sizes required when adding to Base Engine Kit. Base engine kit for diesel applic

ENGINE BASE KIT .020
Base Engine Kit: Includes .20 oversized pistons w/rings, complete gasket set with front and rear crank seals and connecting rod bushings. Rod or main bearings can be added separately. Please indicate the rod and main bearing sizes required when adding to Base Engine Kit. Base engine kit for diesel a

ENGINE BASE KIT .030
Base Engine Kit: Includes .30 oversized pistons w/rings, complete gasket set with front and rear crank seals and connecting rod bushings. Rod or main bearings can be added separately. Please indicate the rod and main bearing sizes required when adding to Base Engine Kit. Base engine kit for diesel

ENGINE BASE KIT .040
Base Engine Kit: Includes .40 oversized pistons w/rings, complete gasket set with front and rear crank seals and connecting rod bushings. Rod or main bearings can be added separately. Please indicate the rod and main bearing sizes required when adding to Base Engine Kit. Base engine kit for diesel a

FROST PLUG HEATER
600 Watt, 120V A/C, 1 3/4"

CIRCULATING TANK HEAT
1000 Watts, 120V

LOWER RADIATOR HOSE H
600 Watt, 1 3/4" Diameter. When installing, check condition of lower hose. If hose is worn or cracked, replace before installation. WARNING: Do not use on Lower Radiator Hose which enters the engine lower than the highest point of the hose.