Ford 3600 Clutch, Transmission & PTO Parts Diagram

PTO CAP

PTO SHAFT
29.46" length , 10 spline w/ (1 1/4" od) x 6 spline w/ (1 1/2"od).

BEARING
ID: 1.998” OD: 3.996” W: 0.801” Countershaft bearing for diesel and gas applications.

STARTER SAFETY SWITCH
Starter safety switch for diesel and gas applications.

SHIFT ARM
ear change lever, long length w/pin on LH side.

SHIFT ARM
Short Hi-Low Range selector shaft w/pin on RH side. Shift arm for diesel and gas applications.

CLUTCH ALIGNMENT TOOL
Dual stage, 29 splines at 1 7/8”. 10 splines at 1”

CLUTCH ALIGNMENT TOOL
Dual Stage, 1 1/8" x 21 splines, 1 5/8" x 25 splines.

CLUTCH ALIGNMENT TOOL
Tool for 1", 15 spline disc using .655" ID pilot bearing.

RELEASE BEARING
ID 2.06 ", OD 3.56", WOA 0.79", sealed roller.

PTO SHAFT SLEEVE
PTO shaft sleeve for diesel and gas applications.

PTO SNAP RING
1 3/8" outside diameter. PTO snap ring for diesel and gas applications.

BEARING
PTO shifter bearing for diesel and gas applications. ID: 1.38:, OD:2.84", W: 0.67"

PTO SHIFTER ARM SPRIN
PTO shifter arm spring for diesel and gas applications.

PTO SHAFT RETAINER GA
PTO Shaft Retainer Gasket for diesel and gas applications.

PTO SHIFTER FORK
PTO shifter fork for diesel and gas applications.

PILOT BEARING
ID: 0.66" (16.992mm), OD: 1.57" (40.005mm), W: 0.47" (11.988mm), double seal.

PTO OUTPUT SHAFT SEAL
Trans oil seal, output. Dimensions OD 2.39" (60mm), ID 1.42" (36mm) and height .50"(13mm)

CLUTCH SHAFT BUSHING (No Longer Available)

GASKET
Gasket, main drive gear retainer

CLUTCH RELEASE SUPPOR

PTO SHIFTER PLATE

PTO SHIFTER ARM

RELEASE BEARING
ID 2.49", OD 4.06", WOA 0.82", sealed roller. For mechanical release systems.

PTO COUNTERSHAFT SEAL
ID: 1.607" (40.82mm), OD: 2.891" (73.43mm), W: .631" (16.03mm)

CLUTCH PLATE DOUBLE
11" Double clutch w/ 29 spline - 8 1/2" PTO disc w/1 7/8" hub, 1.750" flywheel step.

PTO DISC
8 1/2" PTO Disc, 29 spline, 1 7/8" hub, fiber type material.

CLUTCH DISC
11", 10 spline rigid triangular cerametallic disc, 1" hub, three pad type.

CLUTCH DISC
Spring type drive disc OD: 11", ID: 1"-10 spline. Fiber material.

CLUTCH DISC
Drive disc, 11" OD, 15 spline w/1" hub, fiber material.

CLUTCH ALIGNMENT TOOL
Dual stage alignment tool w/1" by 15 splines and 1 7/8" by 29 splines.

CLUTCH KIT
Kit contains 11" 15 spline rigid drive disc E8NN7550BA, 11" 29 spline double pressure plate D8NN7502AA , pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool.

CLUTCH PLATE
Single 11" pressure plate w/four (4) fingers. Will replace the three (3) finger original style.

CLUTCH DISC
Drive disc, 11", 15 splines w/1" hub. Spring damper type w/organic facing material.

CLUTCH PLATE
This pressure plate replaces the original 3 finger design. 11" w/29 spline IPTO hub. Replaces three finger type. Note, for 4000 series with 8 bolts use C5NN7563U for correct mounting bolt pattern. This unit replaces 6 bolt Plate.

CLUTCH DISC
11", 10 spline rigid, 1" hub, fiber type material.

SHIFT ARM
Gear change lever used for cast iron base shift towers. Uses notch on RH side of lever as viewed from operators platform facing forward.

SHIFT ARM
13 1/4" length main gear lever for units produced from 4/68 to 4/69 only. Uses notch on LH side of lever as viewed from operators platform facing forward.

GEAR SHIFT COVER GASK
Fits C5NN7211F.

GASKET

SHIFT BALL
Thread size is 5/16" x 24 UNF thread.

CLUTCH PEDAL BUSHING (No Longer Available)

CLUTCH PEDAL SPRING

PTO RR SHAFT SEAL
1939 thru 1964 with 1-1/8" or 1-3/8" PTO shaft. Seal is 2.45" O.D., 1 5/8" I.D., 5/8" wide. Fits 1965~ as well w/same measurements on shaft.

CONTROL LEVER BALL

CLUTCH KIT
Kit contains 11" 15 spline spring drive disc E8NN7550BA, 11" 29 spline double pressure plate D8NN7502AA, pilot bearing C5NN7600A and release bearing 83914247 includes pilot tool.

CLUTCH KIT
Kit contains 11" 10 spline spring drive disc 87295808, 11" 29 spline double pressure plate D8NN7502AA, pilot bearing C5NN7600A and release bearing 83914247, includes 1"x10 spline 1 7/8"x29 spline pilot tool.

CLUTCH KIT
Kit contains 11" 10 spline triangular cerametallic disc C7NN7550AC, 11" 29 spline double pressure plate D8NN7502AA, pilot bearing C5NN7600A and release bearing 83914247, includes 1"x10 spline 1 7/8" 29 spline pilot tool.

CLUTCH KIT
Kit contains 11" 10 spline rigid drive disc E5NN7550BA, 11" 29 spline double pressure plate D8NN7502AA , pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool.

CLUTCH KIT
Kit contains 11" 10 spline rigid drive disc 87295808, 11" single pressure plate C9NN7563D pilot bearing C5NN7600A and release bearing C0NN7580A, includes pilot tool.

CLUTCH KIT
Kit contains 11" 15 spline spring drive disc E8NN7550AA, 11 single pressure plateC9NN7563D, pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool.

CLUTCH KIT
Kit contains 11" 10 spline three pad triangular type drive disc C7NN7550AC, 11" 29 spline IPTO hub pressure plate with four finger design that will also replace three finger type with six (6) bolt mounting design D8NN7563DB, release bearing 83914247, pilot bearing C5NN7600A, and 1" by 10 spline and

CLUTCH KIT
Kit contains 11" 10 spline rigid drive disc87295808, 11" 29 spline IPTO pressure plate D8NN7563DB, pilot bearing C5NN7600A and release bearing 83914247 , includes pilot tool.

CLUTCH KIT
: Kit contains 11" 15 spline spring drive disc E8NN7550AA, 11" IPTO 29 spline pressure plate D8NN7563DB, pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool. This is the 6 bolt pressure plate version and will not replace the 8 bolt version.

CLUTCH DISC
11" 10 spline 1" hub 4 pad cerametallic disc.

SEAL (No Longer Available)
O.D. 2.194" I.D. 1.067" W. 0.5" Transmission Oil Seal