JavaScript Disabled - Unable to show Cart
There are (196) parts used by this model.
- Found on Diagram:
Brake
-
-
-
-
-
11022900
BRAKE DUST SEAL
Ozone resistant material, steel base. Brake dust seal for diesel and gas applications.
$4.94
-
11022901
No Longer Available
-
11025503
BRAKE DISC
OD is 8.07", ID is 2.10", 22 teeth. 0.750" Facing, Brake disc for diesel and gas applications.
$40.43
-
11025507
BRAKE DISC
OD 8.22", ID 4.48", one notched oblong end. Brake disc for diesel and gas applications.
$8.73
- Found on Diagram:
Clutch, Transmission & PTO
-
-
11120013
BEARING
ID: 1.998” OD: 3.996” W: 0.801” Countershaft bearing for diesel and gas applications.
$66.72
-
-
-
11125046
SHIFT ARM
Short Hi-Low Range selector shaft w/pin on RH side. Shift arm for diesel and gas applications.
$51.45
-
11125502
CLUTCH DISC
Plate is 5.25" outside diameter, 3.85" inside diameter, 0.082" width, 45 tooth inner perimeter. PTO plate for diesel and gas applications.
$14.00
-
11125505
CLUTCH PLATE
5.47" outside diameter by 3.90" inside diameter by 0.068" width, 54 tooth. PTO plate for diesel and gas applications.
$6.56
-
-
-
11126003
PTO SNAP RING
: 1 3/8" outside diameter. PTO snap ring for diesel and gas applications.
$4.42
-
11126004
BEARING
PTO shifter bearing for diesel and gas applications. ID: 1.38:, OD:2.84", W: 0.67"
$11.68
-
-
-
-
11126009
PILOT BEARING
ID: 0.66" (16.992mm), OD: 1.57" (40.005mm), W: 0.47" (11.988mm), double seal.
$5.24
-
11126011
No Longer Available
-
11126012
GASKET
Gasket, main drive gear retainer
$1.09
-
-
-
-
-
11126025
CLUTCH DISC
13", 10 spline rigid disc, 1" hub, fiber type material.
$128.51
-
11126026
CLUTCH DISC
13", 10 spline, 1" hub w/damper springs, fiber type material.
$114.59
-
11126036
CLUTCH PLATE
13" pressure plate assembly w/29 spline 1 7/8" IPTO hub. Four finger w/ring.
$306.45
-
11126045
SHIFT ARM
Gear change lever used for cast iron base shift towers. Uses notch on RH side of lever as viewed from operators platform facing forward.
$49.03
-
11126046
SHIFT ARM
13 1/4" length main gear lever for units produced from 4/68 to 4/69 only. Uses notch on LH side of lever as viewed from operators platform facing forward.
$46.68
-
-
-
-
11126054
No Longer Available
-
-
11126057
PTO RR SHAFT SEAL
1939 thru 1964 with 1-1/8" or 1-3/8" PTO shaft. Seal is 2.45" O.D., 1 5/8" I.D., 5/8" wide. Fits 1965~ as well w/same measurements on shaft.
$5.18
-
-
-
11126163
CLUTCH KIT
Kit contains 13" 10 spline spring drive disc with 1" hub E7NN7550BB, 13" 29 spline IPTO pressure plate C5NN7563AC, pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool.
$417.01
-
11126164
CLUTCH KIT
Kit contains 13" 10 spline rigid drive disc with 1" hub F0NN7550BA 13" 29 spline IPTO pressure plate C5NN7563AC, pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool.
$417.25
-
12126007
CLUTCH DISC
Friction Disc, ID: 3.65" (92.7mm) w/ 45 teeth, OD: 5.24" (133.1mm), Ht: .0629" (1.6mm)
$23.61
- Found on Diagram:
Cooling
-
-
-
-
11066200
WATER PUMP
Front pump only, single groove v-belt pulley. Mounting holes 5/16" and 7/16" and will replace earlier units w/smaller mounting holes. Includes both pump and housing gaskets (Atlantic #E6NN8513AA and E5NN8507AB).
$64.58
-
11066201
WATER PUMP
Front pump only, double groove v-belt pulley. Includes both pump and housing gaskets (Atlantic #E5NN8507AB).
$114.77
-
11066204
WATER PUMP
Single pulley hub for bolt on fan, complete pump including back plate. For models w/o heater plug or cab heater.
$95.27
-
-
-
11066294
RADIATOR HOSE
Upper Radiator Hose 1 1/2" I.D. for Gasoline Models.
$13.64
-
-
-
-
-
-
-
-
-
11066310
RADIATOR HOSE
1.5" inside diameter, upper hose for Diesel models.
$6.34
-
11066313
RADIATOR
Core height 17 3/4", width 17 1/2",depth 2". Filler neck is 3/4" height. Four (4) row, Nine (9) fins per inch. W/O oil cooler. Copper core.
$433.43
-
12060156
INLET HOSE
ID: 2"(50MM) L: 2.375" (60.00mm), OD: 2.4" (60.97mm)
$7.17
- Found on Diagram:
Electrical
-
11000100
5IN DIESEL STARTER
OE Lucas unit. DD, 2.8KW, 12v, 10 tooth drive. Uses D2NN11390A solenoid. Uses E4NN11350AA drive. Starter for Ford/New Holland diesel applications.
$246.79
-
11000100A
STARTER, AFTERMARKET
12v, 10 tooth, 2.8KW. Aftermarket unit, not OE Lucas, as 83981923. Uses D7NN11390B Atlantic solenoid and C5NF11350C Atlantic drive. Note: Warranty is six (6) months from date of purchase, unit replacement only. Starter for Ford/New Holland diesel applications.
$217.22
-
11000105
STARTER
Gear reduction option for D8NN11000CE. Starter for Ford/New Holland diesel applications.
$235.95
-
11000112
STARTER
12v, 10 tooth, DD unit. Uses C5NF-11A108-A drive. Uses D2AF11450A solenoid. For 3 Cylinder Gas.
$190.64
-
-
-
-
11000301
STARTER DRIVE
For 4.5"Lucas (M45), 10 tooth, CW, fits 12spline armature, 17mmID, 40mmGr, 70mmL, 60mmOD.
$58.42
-
11000410
BATTERY CABLE
34" Length. Negative battery cable for diesel and gas applications.
$24.30
-
11000411
BATTERY CABLE
36-1/2" Length. Positive battery cable for diesel and gas applications.
$34.56
-
-
11000540
COIL
6v (w/o resistor) or 12v (w/resistor), oil filled. Includes bracket and resisitor.
$18.96
-
11000550
REGULATOR
12v, 14.1 volt set, Four prong (two male-two female) connector for Motorolla style alternators w/external regulator. Fits ref#'s D5NN10300D and D5NN10300E. If regulator is not used with correct alternator, unit will not charge. Non-adjustable.
$38.92
-
11000560
REGULATOR
12v, round terminal plug with four male connectors. Fits units w/Motorolla equipped.
$79.73
-
-
11000906
BULB
14v maximum, 3.8 watt, miniature bayonet base. Priced individually, sold in multiples of 10. Bulb for diesel and gas applications. Type 1895.
$1.07
-
11000907
BULB
12.8v, 23 watt, double contact bayonet base. Priced individually, sold in multiples of 10. Type 1076.
$1.07
-
11000909
BULB
12v, 27/8.3 watt, double bayonet base. Type 1157. Priced individually, sold in multiples of 10.
$0.63
-
11000916
BULB
12v, 55 watt, PK22S base. Bulb for diesel and gas applications. Type H3-55.
$4.88
-
11000935
FUSE
AGC25 Fuse for diesel and gas applications, Priced Individually, Sold in Multiples of 5
$0.33
-
11000950
DIESEL STARTER BUSHIN
17.10mm ID, 21.04mm OD, 22.10mm L. Sintered brass material. Starter bushing for diesel applications.
$2.35
-
11000960
IGNITION SWITCH
Seven terminal Lucas type with cold start. Rated at max 35 amp load. Ignition switch for diesel and gas applications.
$13.34
-
11000968
IGNITION KEY
Priced individually, sold in multiples of 2. Ignition key for diesel and gas applications.
$1.91
-
-
11000984
HOLD DOWN W/ NUT
1965~, 7" L by 5/16"x18 thread pitch. Battery Hold Down with nut for diesel and gas applications.
$3.66
-
11006005
REAR LAMP LENS
Red Lens, tail light / brake light lens, fits original style housing.
$24.29
-
11006015
HEADLAMP
Headlight assembly, 12 volt sealed beam
$60.58
-
11006102
DISTRIBUTOR
For 3 cyl gas engines. Mechanical advance only; No provision for vacuum advance
$281.68
-
12000100
STARTER
12v, 10 tooth, 2.8KW, Direct Drive, LH mount. Uses 1200-0200 solenoid and 1200-0300 drive. 3.50" CTC mount. Note, on some MF175 models using Delco 20MT #1107872 or 1109261 use Delco type 28MT 6630180. Starter for diesel applications.
$270.85
-
12000203
SOLENOID
12v, three terminal, switch terminal is male spade. For Lucas and Marelli units.
$45.20
- Found on Diagram:
Engine
-
11091040
VALVE TRAIN KIT
Valve train kit consists of intake and exhaust valves, springs, keepers and valve seals. Valve train kit for diesel 3 cyl engine applications.
$119.20
-
-
-
-
11091172
ROD BEARINGS .020
0.020" Oversize rod bearings for diesel and gas 3 cylinder applications.
$35.12
-
11091271
CAMSHAFT BUSHING
Camshaft bushing for diesel and gas applications. Four used in three cylinder applications, five used in four and six cylinder applications.
$7.61
-
-
-
-
-
-
-
-
11099409
OIL CAP
Plug type cap, screw in to tighten.
$13.23
-
-
-
-
-
-
-
11099523
PRE CLEANER
Air intake cap for 2" pipe, black in color.
$16.10
-
11099524
PRE CLEANER
Air intake cap for 2 1/4" pipe, black in color.
$15.11
-
-
-
11099901
MANIFOLD
Three (3) cylinder horizontal exhaust manifold. Uses Atlantic E8NN9448AA exhaust gasket.
$74.92
-
-
- Found on Diagram:
Filters
-
AF1311
AIR FILTER
Air filter for diesel and gas applications.
$78.25
-
AF2036
AIR FILTER
Dimensions: Inner filter, OD: 2-15/16", ID: 17/32" & 2-13/32", Length: 9-15/16". Air filter for diesel applications.
$11.76
-
FF2608
FUEL FILTER
In-Line Fuel Filter for 5/16" Fuel filter for diesel and gas applications.
$2.71
-
FF3000
Fuel Filter
Fuel filter for diesel and gas applications.
$3.66
-
HF4431
LUBE FILTER
Dimensions: OD: 3.7" (94mm), Length: 6.93" (168mm), Thread: 1.125" x 16 UNF, Features: By-Pass Valve. Lube filter for diesel and gas applications.
$11.90
-
OF2664
LUBE FILTER
Features: Anti-Drainback Valve, Front-End Check Valve, Super High Pressure By-Pass Valve (30-45 PSID). Lube filter for diesel and gas applications.
$9.97
-
OF3101
LUBE FILTER
Features: Anti-Drainback Valve, By-Pass Valve. Lube filter for diesel and gas applications.
$5.75
- Found on Diagram:
Front Axle & Steering
-
11044064
STEERING NUT
Steering nut for diesel and gas applications. 11/16" x 24 pitch (NF)
$6.39
-
-
11084008
KING PIN REPAIR KIT
Kit includes King Pin, 2 bushings, thrust bearing, O-ring seal, retaining wedge bolt and zerk fitting.
$134.28
- Found on Diagram:
Fuel
-
-
11033199
INJECTOR SEAL KIT
For all FNH 'long body' type injectors. Includes cork dust seal, copper compression seal and 2 aluminum return line seals.
$2.81
-
11033200
INJECTOR
Does not include washers, order 1103-3199 seal kit for washers and cork seal. Open Pressure 200-216.
$77.24
-
-
-
-
-
11033404
FUEL SENDER
For fuel tanks using lock ring design sending unit. Fits Atlantic E3NN9002AB. Fuel sender for diesel applications.
$56.89
-
11033407
FUEL TAP
Tank tap is 7/8" tapered by 14 pitch, fuel line is 1/2" by 20 pitch.
$14.20
-
11033408
FUEL BOWL
Flat bottom type. Fuel bowl for diesel applications with 1" bottom hole.
$6.78
-
11033409
FUEL TANK
Original style Lock Ring Fuel Tank, for tractors equipped with lock ring type sender, does not include gasket, lock ring, fuel cap or fuel tap. Can replace E3NN9002KB fuel tank if D8NN9A316KA sender, E2NN1276AA gasket and C5NN9N283A twist lock are used.
$238.33
-
11033411
FUEL TAP SCREEN
Replaceable plastic fuel screen filter for fuel tap used on three and four cylinder models, used on Atlantic E2NN9N024AA.
$2.93
-
11033900
CONTROL CABLE
55-3/4" long. Control cable for diesel and gas applications.
$10.02
- Found on Diagram:
Gauges, Instruments, Cables
-
11070001
CABLE
Brass material, 4-1/4" length. Cable for diesel and gas applications. With alternator.
$7.01
-
11070003
TACH CABLE
Vinyl cased tachometer cable, 48" length, for diesel and gas applications and models w/o cab.
$14.50
-
11072701
GAUGE CLUSTER
CCW tach rotation. Does not include harness. Gauge cluster for diesel and gas applications.
$187.18
-
11072705
GAUGE CLUSTER
For models w/mechanical tach. Gauge cluster assembly for diesel and gas applications.
$257.41
- Found on Diagram:
Hitch and Implement
-
11130500
LEVELING BOX
Adjusts from 27 1/4" to 32 1/4". Fork is 21"L. Cat I. Top knuckle 5/8" ID, Lower fork 3/4" ID.
$95.27
-
-
11132007
TOP LINK
Category II OE style toplink, with lever lock, collapsed length apx. 27".
$72.60
-
11132008
TOP LINK
Dual Category OE style toplink with lever lock, Cat II (1") tractor end, Cat I (3/4") implement end, collapsed length apx. 27".
$106.11
- Found on Diagram:
Hydraulic & Power Steering
-
11011005
POWER STEERING SEAL K
Power steering pump seal repair kit. Services Atlantic E6NN3K514EA99M, E6NN3K514AB, E0NN3K514AB pumps.
$11.68
-
-
11011008
HYDRAULIC PUMP SEAL
Power steering pump front drive gear shaft seal. .64" (16.2mm) ID, 1.02: (28.83mm) OD, .25" (6.35mm width.
$3.22
-
11011009
PUMP REPAIR KIT
Minor repair kit for units w/cast-iron piston type pump. For models w/o IPTO only. Not compatible w/NCA600C or NCA600F pumps.
$38.92
-
11011020
HYDRAULIC PUMP
Small Pump, Gear style unit, center mounted, W/ Independent PTO, W/ Hydraulic Lift. Without Syncro trans, for 8x2 trans.
$654.53
-
11011021
SEAL
For cylinders w/50mm rod x 100mm bore.
$8.92
-
11011022
SEAL
For cylinders w/50mm rod x 110mm bore.
$9.93
-
11011023
SEAL
For cylinders w/50mm rod x 100mm bore.
$15.94
-
-
-
-
-
-
-
-
-
11011163
HYDRAULIC PUMP SHAFT
Rubber reinforced seal with inside diameter of .935", outside diameter 2" and width .530".
$3.69
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
11084020
HUB
Hub, Hydraulic coupler. 5 1/4" overall diameter, 4 mounting holes 7/16" diameter, smooth type, 3 7/8" spacing. 13 spline center bore, 7/8" diameter.
$75.47
- Found on Diagram:
Seats
-
30100009
SEAT
Blue seat cushion and pan assembly with drain hole. For Deluxe Suspension Seat
$150.22
-
30100016
SEAT
Black seat cushion and pan assembly with drain hole. For Deluxe Suspension Seat
$150.22
- Found on Diagram:
Sheet Metal and Grille
-
11111461
TOOL BOX
Tool box is fender mounted. May need to be painted for color matching.
$49.30
-
11112001
SUPPORT ROD
Support rod, 18.5" length, for diesel and gas applications.
$8.65
-
11112002
HOOD HANDLE
Hood handle for diesel and gas applications.
$8.22
-
11116000
BATTERY TRAY
Battery tray for diesel applications w/ 128 AH battery. Shipped with a protective primer finish allowing for a better match to exact paint scheme.
$88.11
- Found on Diagram:
Wheels, Hubs
-
11080001
No Longer Available
-
11080002
WHEEL STUD
1/2"-20 pitch with 1-1/8" usable thread, 2" overall shaft length. Wheel stud for diesel and gas applications. SOLD IN QUANTITIES OF 6.
$1.18
-
11084063
HUB
Bare Hub Only. Requires NH Ref# 312520 and 5127125 bearings, not included. Hub for diesel and gas applications.
$75.88
-
30081019
RIM
16x4.5, 4 5/8" Pilot, 6 Lug
$80.09