JavaScript Disabled - Unable to show Cart
There are (435) parts used by this model.
- Found on Diagram:
Brake
-
-
11022005
SPRING
Brake shoe adjusting screw spring
$5.41
-
11022010
BRAKE DRUM
Cast iron type. 16" outside diameter, 13 7/8" inside diameter.
$121.68
-
-
-
-
-
-
11022900
BRAKE DUST SEAL
Ozone resistant material, steel base. Brake dust seal for diesel and gas applications.
$4.94
-
11022901
No Longer Available
-
11025503
BRAKE DISC
OD is 8.07", ID is 2.10", 22 teeth. 0.750" Facing, Brake disc for diesel and gas applications.
$40.43
-
11025506
BRAKE DISC
6" outside diameter w/60 external teeth.
$5.40
-
11025507
BRAKE DISC
OD 8.22", ID 4.48", one notched oblong end. Brake disc for diesel and gas applications.
$8.73
- Found on Diagram:
Clutch, Transmission & PTO
-
-
11120010
PTO SHAFT
29.46" length , 10 spline w/ (1 1/4" od) x 6 spline w/ (1 1/2"od).
$104.17
-
11120013
BEARING
ID: 1.998” OD: 3.996” W: 0.801” Countershaft bearing for diesel and gas applications.
$66.72
-
-
-
11125045
SHIFT ARM
Gear change lever, long length w/pin on LH side.
$54.98
-
11125046
SHIFT ARM
Short Hi-Low Range selector shaft w/pin on RH side. Shift arm for diesel and gas applications.
$51.45
-
11125502
CLUTCH DISC
Plate is 5.25" outside diameter, 3.85" inside diameter, 0.082" width, 45 tooth inner perimeter. PTO plate for diesel and gas applications.
$14.00
-
11125505
CLUTCH PLATE
5.47" outside diameter by 3.90" inside diameter by 0.068" width, 54 tooth. PTO plate for diesel and gas applications.
$6.56
-
-
-
-
-
11126003
PTO SNAP RING
1 3/8" outside diameter. PTO snap ring for diesel and gas applications.
$4.42
-
11126004
BEARING
PTO shifter bearing for diesel and gas applications. ID: 1.38:, OD:2.84", W: 0.67"
$11.68
-
-
-
-
11126009
PILOT BEARING
ID: 0.66" (16.992mm), OD: 1.57" (40.005mm), W: 0.47" (11.988mm), double seal.
$5.24
-
11126010
PTO OUTPUT SHAFT SEAL
Trans oil seal, output. Dimensions OD 2.39" (60mm), ID 1.42" (36mm) and height .50"(13mm)
$5.70
-
11126011
No Longer Available
-
11126012
GASKET
Gasket, main drive gear retainer
$1.09
-
-
-
-
11126017
RELEASE BEARING
ID 2.49", OD 4.06", WOA 0.82", sealed roller. For mechanical release systems.
$30.20
-
-
-
11126029
CLUTCH DISC
11", 15 spline, 1" hub, rigid disc, fiber type material.
$104.17
-
11126030
CLUTCH PLATE DOUBLE
11" Double clutch w/ 29 spline - 8 1/2" PTO disc w/1 7/8" hub, 1.750" flywheel step.
$444.66
-
11126032
PTO DISC
8 1/2" PTO Disc, 29 spline, 1 7/8" hub, fiber type material.
$91.41
-
11126034
CLUTCH DISC
11", 10 spline rigid triangular cerametallic disc, 1" hub, three pad type.
$121.69
-
11126035
CLUTCH DISC
Spring type drive disc OD: 11", ID: 1"-10 spline. Fiber material.
$105.23
-
11126037
CLUTCH DISC
Drive disc, 11" OD, 15 spline w/1" hub, fiber material.
$120.57
-
-
11126039
CLUTCH KIT
Kit contains 11" 15 spline rigid drive disc E8NN7550BA, 11" 29 spline double pressure plate D8NN7502AA , pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool.
$564.21
-
11126043
CLUTCH PLATE
This pressure plate replaces the original 3 finger design. 11" w/29 spline IPTO hub. Replaces three finger type. Note, for 4000 series with 8 bolts use C5NN7563U for correct mounting bolt pattern. This unit replaces 6 bolt Plate.
$284.45
-
11126044
CLUTCH DISC
11", 10 spline rigid, 1" hub, fiber type material.
$120.52
-
11126045
SHIFT ARM
Gear change lever used for cast iron base shift towers. Uses notch on RH side of lever as viewed from operators platform facing forward.
$49.03
-
11126046
SHIFT ARM
13 1/4" length main gear lever for units produced from 4/68 to 4/69 only. Uses notch on LH side of lever as viewed from operators platform facing forward.
$46.68
-
-
11126049
TRANSMISSION COVER AS
For 6, 7, and 8 speed type from 1965 through 1974. Stamped steel, Includes brass fill plug, (2) shift levers, knobs, and boots. Uses 82004680 gasket sold separately.
$133.31
-
-
-
-
11126054
No Longer Available
-
-
11126057
PTO RR SHAFT SEAL
1939 thru 1964 with 1-1/8" or 1-3/8" PTO shaft. Seal is 2.45" O.D., 1 5/8" I.D., 5/8" wide. Fits 1965~ as well w/same measurements on shaft.
$5.18
-
-
11126061
CLUTCH KIT
Kit contains 11" 15 spline spring drive disc E8NN7550BA, 11" 29 spline double pressure plate D8NN7502AA, pilot bearing C5NN7600A and release bearing 83914247 includes pilot tool.
$563.48
-
-
11126064
CLUTCH PLATE
11" single pressure plate, four (4) finger type.
$210.56
-
-
11126075
CLUTCH KIT
Kit contains 11" 10 spline spring drive disc 87295808, 11" 29 spline double pressure plate D8NN7502AA, pilot bearing C5NN7600A and release bearing 83914247, includes 1"x10 spline 1 7/8"x29 spline pilot tool.
$585.16
-
11126076
CLUTCH KIT
Kit contains 11" 10 spline triangular cerametallic disc C7NN7550AC, 11" 29 spline double pressure plate D8NN7502AA, pilot bearing C5NN7600A and release bearing 83914247, includes 1"x10 spline 1 7/8" 29 spline pilot tool.
$563.48
-
11126090
CLUTCH KIT
Kit contains 11" 10 spline rigid drive disc E5NN7550BA, 11" 29 spline double pressure plate D8NN7502AA , pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool.
$542.52
-
11126105
CLUTCH KIT
Kit contains 11" 10 spline rigid drive disc 87295808, 11" single pressure plate C9NN7563D pilot bearing C5NN7600A and release bearing C0NN7580A, includes pilot tool.
$403.39
-
11126112
CLUTCH KIT
Kit contains 11" 15 spline spring drive disc E8NN7550AA, 11 single pressure plateC9NN7563D, pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool.
$447.25
-
11126113
CLUTCH KIT
Kit contains 11" 10 spline three pad triangular type drive disc C7NN7550AC, 11" 29 spline IPTO hub pressure plate with four finger design that will also replace three finger type with six (6) bolt mounting design D8NN7563DB, release bearing 83914247, pilot bearing C5NN7600A, and 1" by 10 spline and
$390.70
-
11126120
CLUTCH KIT
Kit contains 11" 10 spline rigid drive disc87295808, 11" 29 spline IPTO pressure plate D8NN7563DB, pilot bearing C5NN7600A and release bearing 83914247 , includes pilot tool.
$379.83
-
11126131
CLUTCH KIT
Kit contains 11" 15 spline spring drive disc E8NN7550AA, 11" IPTO 29 spline pressure plate D8NN7563DB, pilot bearing C5NN7600A and release bearing 83914247, includes pilot tool. This is the 6 bolt pressure plate version and will not replace the 8 bolt version.
$431.29
-
11126191
CLUTCH KIT
LuK RepSet®, clutch kit, includes 13" (330mm), 8 bolt, pressed steel, diaphragm spring, fixed 1 7/8"-29 spline PTO hub, single pressure plate, 10 spline dampened organic disc, 100mm OD, 63.5mm ID release bearing, 40mm OD, 17mm ID pilot bearing. For models w/ Non-Synchro Trans.
$850.50
-
11126192
CLUTCH KIT
LuK RepSet®, clutch kit, includes 13" (330mm), 8 bolt, pressed steel, diaphragm spring, fixed 1 7/8"-29 spline PTO hub, single pressure plate, 10 spline rigid organic disc, 100mm OD, 63.5mm ID release bearing, 40mm OD, 17mm ID pilot bearing. For models w/ Non-Synchro Trans.
$783.93
-
11126201
CLUTCH DISC
11" 10 spline 1" hub 4 pad cerametallic disc.
$152.04
-
11126626
No Longer Available
-
11126628
SEAL
Single Lip Oil seal, transmission drive gear, trans input shaft, also for combination trans Step Up/Down. ID: 1.375" (34.93mm), OD: 2.004" (50.9mm), W: 0.328" (8.33mm)
$6.39
-
12126007
CLUTCH DISC
Friction Disc, ID: 3.65" (92.7mm) w/ 45 teeth, OD: 5.24" (133.1mm), Ht: .0629" (1.6mm)
$23.61
- Found on Diagram:
Cooling
-
-
-
-
-
11066200
WATER PUMP
Front pump only, single groove v-belt pulley. Mounting holes 5/16" and 7/16" and will replace earlier units w/smaller mounting holes. Includes both pump and housing gaskets (Atlantic #E6NN8513AA and E5NN8507AB).
$64.58
-
11066204
WATER PUMP
Single pulley hub for bolt on fan, complete pump including back plate. For models w/o heater plug or cab heater.
$95.27
-
-
-
11066294
RADIATOR HOSE
Upper Radiator Hose 1 1/2" I.D. for Gasoline Models.
$13.64
-
11066297
FAN SHROUD
Fiberglass type must drill holes for proper fitment.
$85.36
-
-
-
-
-
-
-
11066310
RADIATOR HOSE
1.5" inside diameter, upper hose for Diesel models.
$6.34
-
11066311
RADIATOR
Core is 16 1/2" high, 17 3/8" wide, 2 1/4" deep. Filler neck height 3/4", Inlet 1 1/2", outlet 1 3/4". Four (4) row, Nine (9) fins per inch. W/O cooler. Copper core.
$325.04
-
-
12060156
INLET HOSE
ID: 2"(50MM) L: 2.375" (60.00mm), OD: 2.4" (60.97mm)
$7.17
- Found on Diagram:
Electrical
-
11000100
5IN DIESEL STARTER
OE Lucas unit. DD, 2.8KW, 12v, 10 tooth drive. Uses D2NN11390A solenoid. Uses E4NN11350AA drive. Starter for Ford/New Holland diesel applications.
$246.79
-
11000100A
STARTER, AFTERMARKET
12v, 10 tooth, 2.8KW. Aftermarket unit, not OE Lucas, as 83981923. Uses D7NN11390B Atlantic solenoid and C5NF11350C Atlantic drive. Note: Warranty is six (6) months from date of purchase, unit replacement only. Starter for Ford/New Holland diesel applications.
$217.22
-
11000105
STARTER
Gear reduction option for D8NN11000CE. Starter for Ford/New Holland diesel applications.
$235.95
-
11000112
STARTER
12v, 10 tooth, DD unit. Uses C5NF-11A108-A drive. Uses D2AF11450A solenoid. For 3 Cylinder Gas.
$190.64
-
-
-
-
-
11000300
STARTER DRIVE
10 tooth, CW, fits 3 splinw armature, 17mmID, 40mmGr, 70mmL, 60mmOD.
$46.46
-
11000301
STARTER DRIVE
For 4.5"Lucas (M45), 10 tooth, CW, fits 12spline armature, 17mmID, 40mmGr, 70mmL, 60mmOD.
$58.42
-
11000302
STARTER DRIVE
10 tooth, CW, fits 12spline armature, 17mmID, 40mmGr, 73mmL, 60mmOD.
$53.66
-
-
11000410
BATTERY CABLE
34" Length. Negative battery cable for diesel and gas applications.
$24.30
-
11000411
BATTERY CABLE
36-1/2" Length. Positive battery cable for diesel and gas applications.
$34.56
-
11000540
COIL
6v (w/o resistor) or 12v (w/resistor), oil filled. Includes bracket and resisitor.
$18.96
-
11000548
ALTERNATOR
This alternator can be used to replace original generator. Additional brackets and hardware may be needed. See kit # AKT0005.
$140.73
-
11000600
GENERATOR
2v, 22amp, uses 105E10505C regulator. W/Fan and tach drive. Pulley seperate, use C5NF10196B. 1965 on up units.
$140.79
-
11000650
REGULATOR
12v, B circuit. Use with C5NF10000E Lucas generator. 1965 and up units.
$26.77
-
11000651
GENERATOR FAN
For C5NF10000E. Fits Lucas tach drive generator on 2000~7000 series.
$8.71
-
-
11000653
TACH GEAR
For Lucas generators. Fits C5NF10000E.
$7.26
-
11000654
TACH DRIVE ASSEMBLY
For Lucas tach drive generator. Fits Atlantic C5NF10000E. Assembly w/gear and housing.
$21.62
-
-
-
-
11000906
BULB
14v maximum, 3.8 watt, miniature bayonet base. Priced individually, sold in multiples of 10. Bulb for diesel and gas applications. Type 1895.
$1.07
-
11000912
BULB
12v, 4.3 watts, miniature bayonet base. Priced individually but sold in multiples of 10. Type 1816.
$0.44
-
11000916
BULB
12v, 55 watt, PK22S base. Bulb for diesel and gas applications. Type H3-55.
$4.88
-
11000918
BULB
12v, 1.70 watts, miniature bayonet base. Priced individually, sold in multiples of 10. Type 53.
$1.72
-
11000931
FUSE
AGC5, Priced Individually, Sold in Multiples of 5
$0.33
-
11000933
FUSE
AGC15 fuse for diesel or gas applications, Priced Individually, Sold in Multiples of 5
$0.30
-
11000935
FUSE
AGC25 Fuse for diesel and gas applications, Priced Individually, Sold in Multiples of 5
$0.33
-
11000937
FUSE
AGC10, Priced Individually, Sold in Multiples of 5
$0.33
-
11000950
DIESEL STARTER BUSHIN
17.10mm ID, 21.04mm OD, 22.10mm L. Sintered brass material. Starter bushing for diesel applications.
$2.35
-
11000960
IGNITION SWITCH
Seven terminal Lucas type with cold start. Rated at max 35 amp load. Ignition switch for diesel and gas applications.
$13.34
-
11000967
STOP SWITCH
Two prong terminal. Stop switch for diesel and gas applications.
$19.49
-
11000968
IGNITION KEY
Priced individually, sold in multiples of 2. Ignition key for diesel and gas applications.
$1.91
-
11000969
STOP LIGHT SWITCH
12V Stop Light Switch for diesel and gas applications. Two connectors.
$29.24
-
-
11000978
LIGHT SWITCH
Fits numerous 1965~, 3-4-6 cyl's, rotary type switch. Light switch for diesel and gas applications.
$14.63
-
11000984
HOLD DOWN W/ NUT
1965~, 7" L by 5/16"x18 thread pitch. Battery Hold Down with nut for diesel and gas applications.
$3.66
-
-
-
-
-
-
-
11005108
IGN KIT INC. POINTS,
For OHV 3 cyl models. Ignition kit for gas applications.(inc. points, cond, rotor, plug)
$23.83
-
-
11005202
ELECTRONIC IGNITION
Converts mechanical ignition to electronic type. 12v (-) ground for 158, 192, 201 c.i. motors, 1975 on with Motorcraft distributors.
$208.08
-
-
-
11006005
REAR LAMP LENS
Red Lens, tail light / brake light lens, fits original style housing.
$24.29
-
11006015
HEADLAMP
Headlight assembly, 12 volt sealed beam
$60.58
-
11006102
DISTRIBUTOR
For 3 cyl gas engines. Mechanical advance only; No provision for vacuum advance
$281.68
-
12000100
STARTER
12v, 10 tooth, 2.8KW, Direct Drive, LH mount. Uses 1200-0200 solenoid and 1200-0300 drive. 3.50" CTC mount. Note, on some MF175 models using Delco 20MT #1107872 or 1109261 use Delco type 28MT 6630180. Starter for diesel applications.
$270.85
-
12000203
SOLENOID
12v, three terminal, switch terminal is male spade. For Lucas and Marelli units.
$45.20
- Found on Diagram:
Engine
-
-
11091007
PISTON KIT
4.2" Piston, Piston Rings, Piston Clips and Piston Pin for diesel applications.
$159.19
-
-
-
-
-
-
11091022
CONROD BOLT
Conrod bolt for diesel and gas applications.
$4.50
-
11091023
CONROD NUT
onrod nut for diesel and gas applications.
$1.12
-
11091030
LINER
Length 8.25", O.D 4.36" and I.D. 4.2". Semi Finished Liner for diesel applications.
$44.46
-
11091040
VALVE TRAIN KIT
Valve train kit consists of intake and exhaust valves, springs, keepers and valve seals. Valve train kit for diesel 3 cyl engine applications.
$119.20
-
-
-
-
-
-
-
-
-
-
-
-
-
-
11091172
ROD BEARINGS .020
0.020" Oversize rod bearings for diesel and gas 3 cylinder applications.
$35.12
-
-
-
-
-
-
11091270
CAMSHAFT
Camshaft for diesel applications.
$269.12
-
11091271
CAMSHAFT BUSHING
Camshaft bushing for diesel and gas applications. Four used in three cylinder applications, five used in four and six cylinder applications.
$7.61
-
-
11091303
EXHAUST VALVE
Exhaust valve for diesel applications. HOA 145.9mm, SHAFT OD 9.4mm, FACE 38.4mm, UPPER BASE 45°
$11.59
-
11091306
SPRING
Valve spring for diesel applications.
$10.43
-
11091307
SPRING
Valve spring for diesel applications.
$4.50
-
11091308
COTTER KEEPERS
Cotter keepers for diesel applications. Priced individually, Sold Individually.
$1.28
-
-
-
-
-
11097076
SEAL
Seal, conversion flange, for oil filter convertor, 2-quart to 1-quart spin or use with conversion flange 309825
$8.77
-
-
-
-
-
-
11099404
OIL PAN
Stamped steel construction.
$116.94
-
-
-
11099409
OIL CAP
Plug type cap, screw in to tighten.
$13.23
-
-
-
-
-
-
-
-
-
-
11099523
PRE CLEANER
Air intake cap for 2" pipe, black in color.
$16.10
-
11099524
PRE CLEANER
Air intake cap for 2 1/4" pipe, black in color.
$15.11
-
11099900
MANIFOLD
Three (3) cylinder vertical exhaust manifold. Uses E8NN9448AA exhaust gasket.
$70.13
-
11099901
MANIFOLD
Three (3) cylinder horizontal exhaust manifold. Uses Atlantic E8NN9448AA exhaust gasket.
$74.92
-
-
1109D175
ENGINE BASE KIT
Base Engine Kit: Includes standard pistons w/rings, complete gasket set with front and rear crank seals and connecting rod bushings. Rod or main bearings can be added separately. Please indicate the rod and main bearing sizes required when adding to Base Engine Kit. Base engine kit for diesel applic
$422.69
-
1109D17520
ENGINE BASE KIT .020
Base Engine Kit: Includes .20 oversized pistons w/rings, complete gasket set with front and rear crank seals and connecting rod bushings. Rod or main bearings can be added separately. Please indicate the rod and main bearing sizes required when adding to Base Engine Kit. Base engine kit for diesel a
$444.38
-
1109D17530
ENGINE BASE KIT .030
Base Engine Kit: Includes .30 oversized pistons w/rings, complete gasket set with front and rear crank seals and connecting rod bushings. Rod or main bearings can be added separately. Please indicate the rod and main bearing sizes required when adding to Base Engine Kit. Base engine kit for diesel a
$444.38
-
1109D17540
ENGINE BASE KIT .040
Base Engine Kit: Includes .40 oversized pistons w/rings, complete gasket set with front and rear crank seals and connecting rod bushings. Rod or main bearings can be added separately. Please indicate the rod and main bearing sizes required when adding to Base Engine Kit. Base engine kit for diesel a
$444.38
-
-
-
-
30091022
LOWER RADIATOR HOSE H
600 Watt, 1 3/4" Diameter. When installing, check condition of lower hose. If hose is worn or cracked, replace before installation. WARNING: Do not use on Lower Radiator Hose which enters the engine lower than the highest point of the hose.
$68.65
-
30091023
LOWER RADIATOR HOSE H
600 Watt, 2" Diameter. When installing, check condition of lower hose. If hose is worn or cracked, replace before installation. WARNING: Do not use on Lower Radiator Hose which enters the engine lower than the highest point of the hose.
$68.65
- Found on Diagram:
Filters
-
AF1311
AIR FILTER
Air filter for diesel and gas applications.
$78.25
-
AF1503
AIR FILTER
Air filter for diesel and gas applications.
$21.24
-
AF2036
AIR FILTER
Dimensions: Inner filter, OD: 2-15/16", ID: 17/32" & 2-13/32", Length: 9-15/16". Air filter for diesel applications.
$11.76
-
FF3000
Fuel Filter
Fuel filter for diesel and gas applications.
$3.66
-
-
HF9100
LUBE FILTER
Lube filter for diesel and gas applications.
$11.87
-
OF1714
LUBE FILTER
Lube filter for diesel and gas applications.
$24.49
-
OF3101
LUBE FILTER
Features: Anti-Drainback Valve, By-Pass Valve. Lube filter for diesel and gas applications.
$5.75
-
AF1503
AIR FILTER
Air filter for diesel and gas applications.
$21.24
-
AF2036
AIR FILTER
Dimensions: Inner filter, OD: 2-15/16", ID: 17/32" & 2-13/32", Length: 9-15/16". Air filter for diesel applications.
$11.76
-
FF3000
Fuel Filter
Fuel filter for diesel and gas applications.
$3.66
-
-
HF9100
LUBE FILTER
Lube filter for diesel and gas applications.
$11.87
-
OF1714
LUBE FILTER
Lube filter for diesel and gas applications.
$24.49
-
OF3101
LUBE FILTER
Features: Anti-Drainback Valve, By-Pass Valve. Lube filter for diesel and gas applications.
$5.75
- Found on Diagram:
Front Axle & Steering
-
11044008
SPINDLE BEARING
ID is 1.345", OD is 2.2", Width is .622". Spindle bearing for diesel and gas applications.
$6.61
-
-
-
11044018
SPINDLE BUSHING
Height 1.482", OD 1.380", ID 1.25" Spindle bushing for diesel and gas applications.
$4.75
-
11044019
LINK END ASSEMBLY
Front side, 4" center to end, .687" shaft diameter w/18 pitch LH thread.
$14.85
-
11044020
LINK END ASSEMBLY
Rear angled shaft end 4 1/2" LOA, .687" diameter w/18 pitch RH thread.
$14.85
-
11044024
SPINDLE
RH, 11.687"L, 1.25" Upper diameter, 1.340" Lower diameter, 1.25" Inner stub diameter, .750" Outer stub diameter. Keyway is .235"W x .914"L.
$108.26
-
11044026
SPINDLE
LH, 11.687"L, 1.25" Upper diameter, 1.340" Lower diameter, 1.25" Inner stub diameter, .750" Outer stub diameter. Keyway is .235"W x .914"L.
$106.11
-
11044030
SPINDLE SEAL
OD: 1.71" (43.4mm), ID: 1.25" (31.8mm), W: 0.21" (5.3mm).
$1.99
-
11044031
AXLE PIN
Solid Axle Pin. OD: 1.750", Shaft L: 5.960". Can replace C5NN3127A.
$45.07
-
-
11044033
AXLE BUSHING
Front axle bushing, 2.19" outside diameter, 2.05" inside diameter, 1.5" length, non-split design w/inner spiral relief for lubrication. Axle bushing for diesel and gas applications.
$5.40
-
-
-
-
11044048
DRAG LINK END
3/4" by 16 pitch LH threads, 9/16" pin. Drag link end for diesel and gas applications.
$22.52
-
-
-
-
-
11044064
STEERING NUT
Steering nut for diesel and gas applications. 11/16" x 24 pitch (NF)
$6.39
-
-
11044076
STEERING SHAFT
Manual steering shaft w/block asm., 26 1/4" length. Does not come with end nut for steering wheel.
$155.07
-
-
-
-
-
11044170
SEAL
Spindle dust seal with seal with groove and offset rubber for steering arm. OD: 1.71" (43.4mm), ID: 1.25" (31.8mm), W: 0.21" (5.3mm).
$2.13
-
-
11044184
DRAG LINK
Tube Length 28.125" (714.375mm), Overall length 30.10" (790mm)
$135.15
-
-
11044211
FRONT AXLE
Front Axle Center section, includes C7NN3153B bushing
$242.67
-
11044401
STEERING ARM
Spindle steering arm, for manual and power steering models, replaces 957E3130.
$57.93
-
11044450
STEERING GEAR ASSEMBL
Manual steering gear w/18" mainshaft. Sector shafts use D9NN2N289AA seals, already installed. Steering gear assembly for diesel and gas applications.
$648.12
-
11044900
STEERING WHEEL
18" Diameter center hub is 0.785 in, 36 splines. Steering wheel for diesel and gas applications.
$42.25
-
-
11044902
RADIUS BALL CAP
Radius ball cap used w/C5NN3N442C socket. Can be used for LH or RH side. Radius ball cap for diesel and gas applications.
$17.77
-
11044903
RADIUS SPACER
Radius rod socket, used w/ 83924040 cap. Can be used for LH or RH side.
$21.01
-
-
11045218
BEARING CUP
Tapered Cup OD: 2.33" (59.18mm), ID: 2.24" (11.68mm), W: 0.46"
$3.15
- Found on Diagram:
Fuel
-
11030004
CARBURETOR
New Zenith style replacement carb for units with Zenith and Holley carburetors. Center to center 2.65". Note: New carbs are not adjusted to new specs due to age and wear variances of tractors, may need to adjust mixture, idle, and float adjustments.
$346.72
-
-
11030071
CARBURETOR KIT
Major Kit for Holley carburetor R4119, R4120, R855 or R4111 and Ford #'s C7NN9510B, C7NN9510C, D8NN9510AA, D8NN9510BA, CKPN9590B, C7NN9510A and D8NN9510CA.
$39.34
-
-
-
-
11033199
INJECTOR SEAL KIT
For all FNH 'long body' type injectors. Includes cork dust seal, copper compression seal and 2 aluminum return line seals.
$2.81
-
11033200
INJECTOR
Does not include washers, order 1103-3199 seal kit for washers and cork seal. Open Pressure 200-216.
$77.24
-
-
-
-
11033400
FUEL TANK
13 gallons (49.2 litres), for units equipped w/lock ring fuel sender. Fill neck height 2". Note: Will not fit 4000 models. Does not include lock ring or fuel tap. Does include fuel cap. Prior to installation, anti-rust coating should be removed with mineral spirits or lacquer thinner
$193.34
-
-
-
11033404
FUEL SENDER
For fuel tanks using lock ring design sending unit. Fits Atlantic E3NN9002AB. Fuel sender for diesel applications.
$56.89
-
11033407
FUEL TAP
Tank tap is 7/8" tapered by 14 pitch, fuel line is 1/2" by 20 pitch.
$14.20
-
11033411
FUEL TAP SCREEN
Replaceable plastic fuel screen filter for fuel tap used on three and four cylinder models, used on Atlantic E2NN9N024AA.
$2.93
-
-
11033900
CONTROL CABLE
55-3/4" long. Control cable for diesel and gas applications.
$10.02
-
-
11039003
INJECTION PUMP
To replace original pump CAV# 3233F380, 3833F380. To ensure proper fit and function, CAV number must match exactly.
$1,024.08
- Found on Diagram:
Gauges, Instruments, Cables
-
11070003
TACH CABLE
Vinyl cased tachometer cable, 48" length, for diesel and gas applications and models w/o cab.
$14.50
-
-
- Found on Diagram:
Hitch and Implement
-
11130500
LEVELING BOX
Adjusts from 27 1/4" to 32 1/4". Fork is 21"L. Cat I. Top knuckle 5/8" ID, Lower fork 3/4" ID.
$95.27
-
-
-
-
-
11130517
TOP LINK END
Top Link End, CAT II, 1 1/4" LH Thread, 1" Ball ID, OAL 13"
$48.47
-
11130530
FORK
3/4" Thread 14" useable length
$40.07
-
11130533
LIFT ARM BALL
Ball Lift Arm. 1-3/8" wide. Category II. ID 1 9/64"
$5.75
-
-
11131071
CHECK CHAIN KIT
Drawbar check chain kit includes: RH/LH anchors, 2 eyelets, 2 chains, 4 clevis with pins and hdw
$41.07
-
-
-
-
-
-
-
-
-
-
30131390
STABILZER STUB PIN
Stabilize Pin OD: 0.87" (22mm) with 5/8"-18 thread, LOA: 2.72" (69mm), includes nut & lock washer.
$2.59
- Found on Diagram:
Hydraulic & Power Steering
-
11010090
PUMP REPAIR KIT MAJO
Major repair kit for units w/cast-iron piston type pump. For models w/o IPTO only. Not compatible w/NCA600C or NCA600F pumps.
$58.42
-
11010406
PUMP DRIVE SHAFT
Hydraulic Shaft, Pump Drive, 3/4" shaft, 8-7/8" overall length, hub end 2-3/4", ID: 1", 10 spline. 724, 725, 730 & 735 Series loaders
$71.41
-
11010408
PUMP DRIVE COUPLER
Pump Drive Coupler, OD: 5 1/4", Mount Holes: 7/16" diameter, 3-7/8" C to C, Bore: 7/8"x 13 spline. For 730 Series farm loaders and 745 Series Industrial loaders.
$92.86
-
-
-
-
11011005
POWER STEERING SEAL K
Power steering pump seal repair kit. Services Atlantic E6NN3K514EA99M, E6NN3K514AB, E0NN3K514AB pumps.
$11.68
-
-
11011007
AP S PUMP SEAL KIT
Power steering seal kit for units w/vertical resevoir fluid tank, January 1965 to August 1968.
$54.08
-
11011008
HYDRAULIC PUMP SEAL
Power steering pump front drive gear shaft seal. .64" (16.2mm) ID, 1.02: (28.83mm) OD, .25" (6.35mm width.
$3.22
-
11011009
PUMP REPAIR KIT
Minor repair kit for units w/cast-iron piston type pump. For models w/o IPTO only. Not compatible w/NCA600C or NCA600F pumps.
$38.92
-
11011012
HYDRAULIC PUMP
Capacity is 9.5 GPM at 2400 RPM (7.1 GPM at 1800 RPM), 2400 PSI Maximum Pressure. Will not replace piston type pump, gear type only. Requires mounting gasket E4NN911AA, not included. 2-4000 MODELS (3 CYL ONLY).
$511.46
-
11011015
HYDRAULIC PUMP
Gear style unit w/relief valve, transmission mount w/IPTO. GPM 7.4, rear pump 2.3.
$697.86
-
-
-
-
-
-
-
-
-
-
-
11011163
HYDRAULIC PUMP SHAFT
Rubber reinforced seal with inside diameter of .935", outside diameter 2" and width .530".
$3.69
-
-
11011169
WASHER
Hydraulic Lift cylinder back up washer.
$2.70
-
-
-
-
11011703
STEERING CYLINDER
Cylinder with 5/8" Rod (LH/RH). Early style cylinder with D8NN3A304AA female fittings. Can replace original cylinders with 1/2" rod.
$393.56
-
-
11012003
HYDRAULIC VALVE
Single spool double acting hydraulic valve kit. Single spool. (Mounts on lift cover under the seat).
$411.74
-
- Found on Diagram:
Manuals & Decals
-
-
-
-
-
-
11151578
DECAL SET
3000 Ford Diesel Hood Decal Kit (68-75)
$49.75
-
11151579
DECAL SET
3000 Ford Gas Hood Decal Set (68-75)
$50.52
-
- Found on Diagram:
Muffler
-
11172001
MUFFLER
Vertical -Round Body. Shell Dia 5-1/2"
$46.57
-
11172002
MUFFLER
Horizontal- Oval Body. Shell Dia 4" x 8"
$67.14
-
11172205
MUFFLER
Vertical -Oval Body. Shell 4-1/2" x 9"
$121.28
-
11172300
MUFFLER
Vertical -Oval Body. Shell 4-1/2" x 9"
$147.99
-
-
11172550
MUFFLER
When using this muffler, must also use FO-5A adapter. Vertical -Oval Body. Shell 4" x 8"
$88.77
-
11172551
No Longer Available
-
11176007
MUFFLER
Horizontal- Oval Body. Shell Dia 4" x 8", CUSTOM STANLEY DESIGN
$76.32
-
-
- Found on Diagram:
Rear Axle
-
-
-
-
11055212
BEARING CUP
main drive gear, countershaft, output shaft
$9.45
-
-
11057000
RR AXLE SHAFT BEARING
Bearing spacer only, w/ or w/o differential lock. Does not include roller bearing or race. Collar, ID: 3.22", OD: 3.45", W: 1.21".
$32.41
-
-
-
-
- Found on Diagram:
Seats
-
-
30100009
SEAT
Blue seat cushion and pan assembly with drain hole. For Deluxe Suspension Seat
$150.22
-
30100016
SEAT
Black seat cushion and pan assembly with drain hole. For Deluxe Suspension Seat
$150.22
- Found on Diagram:
Sheet Metal and Grille
-
11111453
RADIATOR COVER
Radiator Shell. 2000, 3000, 4110, 4140 w/ wet air cleaner, all others w/ dry air cleaner. Shipped with a protective primer finish allowing for a better match to exact paint scheme.
$444.27
-
11111454
FENDER W/BRACKET RH/
4000 (except HiClear, 1958 to 1964) 535 (1975 to 1981), 530A (1981 to 1990). Shipped with a protective primer finish allowing for a better match to exact paint scheme.
$205.82
-
-
11111550
FENDER SKIN
Rear fender skin without mounting bracket. Fender is for right or left side. Shipped with a protective primer finish allowing for a better match to exact paint scheme.
$110.44
-
11112000
TOOL BOX
15" long 4 1/2" width and height. May need to be painted for color matching.
$43.24
-
11112001
SUPPORT ROD
Support rod, 18.5" length, for diesel and gas applications.
$8.65
-
11112002
HOOD HANDLE
Hood handle for diesel and gas applications.
$8.22
-
-
-
11115004
GRILL
Upper Plastic Grille.
$22.31
-
-
-
-
-
11115401
BUMPER
High quality Axle Mount bumper. Shipped with a protective primer finish allowing for a better match to exact paint scheme.
$307.33
-
11115409
FRONT GRILLE
Lower Grill w/ inset headlights, start year 1968
$48.40
-
11115417
RUNNING BOARD
Left Platform Assembly (Foot Board), for units w/ hand brake. Shipped with a protective primer finish allowing for a better match to exact paint scheme.
$51.92
-
11115419
RADIATOR SHELL
Radiator Cover, 2000, 3000, 4140 w/ dry air cleaner, all others w/ wet air cleaner. Shipped with a protective primer finish allowing for a better match to exact paint scheme.
$541.81
-
11115421
RUNNING BOARD
Left Platform (foot board). Shipped with a protective primer finish allowing for a better match to exact paint scheme.
$83.42
-
11115422
RUNNING BOARD
Right Platform Assembly (foot board). Shipped with a protective primer finish allowing for a better match to exact paint scheme.
$83.42
-
11116000
BATTERY TRAY
Battery tray for diesel applications w/ 128 AH battery. Shipped with a protective primer finish allowing for a better match to exact paint scheme.
$88.11
- Found on Diagram:
Wheels, Hubs
-
11080001
No Longer Available
-
11080002
WHEEL STUD
1/2"-20 pitch with 1-1/8" usable thread, 2" overall shaft length. Wheel stud for diesel and gas applications. SOLD IN QUANTITIES OF 6.
$1.18
-
-
11080103
RIM STOP SCREW
Screw, for stop body. Use with power adjust rims PAR10X28, C5NN1050J, and C5NN1050H.
$4.66
-
11082000
DISC, WHEEL
Rear wheel 28"& 32", 8-bolt hub, 6-bolt rim
$315.93
-
11084001
FRONT HUB KIT
Kit contains 1 of 957E1139 dust cap, 1 of EHPN1200E wheel bearing kit, 6 of C5NN1012B wheel nuts. 6 of C5NN1107F wheel studs, and 1 of C9NN1104F hub.
$95.89
-
-
11084006
DUST CAP
W/zerk tap, zerk fitting not included.
$7.01
-
11084007
TAB WASHER
OD 1.50" (38.20mm). ID .775" (19.70mm), Thickness 1/16"(1.23mm).
$0.90
-
-
-
11084042
BEARING CONE CUP
Inner wheel bearing and race 4000, ref #'s 86516467/86516468. ID: 0.75", OD: 1.78", WOA: 0.61".
$10.54
-
-
11084060
HUB W/OUT BEARING
Bare hub only, uses Atlantic EHPN1200E wheel bearing kit. Seal on hub ID 2.669", Inner race ID on hub 2.38", Outer race ID on hub 1.786".
$62.04
-
11084063
HUB
Bare Hub Only. Requires NH Ref# 312520 and 5127125 bearings, not included. Hub for diesel and gas applications.
$75.88
-
11088000
WHEEL BEARING KIT
Contians: Seal type TCM1682713, Outer Race Type LM11910, Outer Bearing type LM11949, Inner Race type LM67010, Inner Bearing type LM67048.
$18.02
-
30081011
RIM
28x12, 6 Lug, Rim is shipped bare metal unless pallet quantity ordered
$234.00
-
30081012
RIM
28x10, 6 Lug, Rim is shipped bare metal unless pallet quantity ordered
$175.48
-
30081015
RIM
28x11, 6 Lug with 24" center to center of Lugs across rim, Rim is shipped bare metal unless pallet quantity ordered
$201.22
-
30081019
RIM
16x4.5, 4 5/8" Pilot, 6 Lug
$80.09